Imperial Shuttle Tydirium

I'd love to know this as well so I can continue the upgrade of the Shuttles I got fro Rich?

I also think there may be an A wing ID in there?
 
Credit for this find goes to pro kit part hunter and scratch builder Big John Curilla.. John said he was going through known used ROTj kits (donor for AT-St) and found the Shuttle jack pot... the kit has 8 parts. the kit you seek is the 1/32 Tamiya F-14 Tomcat

Thanks againt to John and Neil for the opportunity to re release this kit in all its accurate glory!

Steve
 
Thank you guys ! And kudos John !! Very nice find ;)
It looks like we need 2 kits for a shuttle, I think I gonna buy a set of castings from you Steve !
 
John also found the rods with circle details on the ends on the bottom of the shuttle... there are four of them .. from the Tamiya 1/25 Centurion... John is a machine! Neil used parts form the gun motor carrige on his master. Tox no problem on the parts.. i'll just put them in the box with the tie parts.

I need your address again..

Steve
 
Great find John once again and thanks for sharing Steve ! Now I dont know if I will be able to remove the ones of my bulkhead :s

Thanks Steve,

Gonna drop you a pm !
 
Last edited:
REL said:
I put bluetape over the window, cutting it perfectly to shape...

ss_ty_build_16.jpg


...then took the tape off in one piece, laid it on a piece of thin clear styrene, using it as a guide to cut out the window, cutting it a little larger so I could fine tune it, then using a hair dryer (a heat gun was too hot and warped it) slowly bent it to shape.

It took about 3 tries to get it right. After I got it the right shape, I painted the back of the glass flat black.
Click to expand...

WOW! I'm probably echoing everyone else here, but this is the first time I have seen this. Truly amazing. And thanks for the info on making the window.
 
Getting closer guys!

384590127.jpg

384590133.jpg


Hardest thing Ive had to do... cut apart Neil's master patter!! (well built by the way very smartly done.. Neil you are a true master! I hope I can do justice to this piece of art you have created! I have a plan for upper and lower shells on a alluminum and acrylic armeture.. had to be done.. pressure cast no bubbles.... resin will not support any part of the model..

384590139.jpg

384590150.jpg


thanks for looking

Steve
 
Holy Sh1t! :wacko That couldn't have been much fun. How the hell did you cut through all that acrylic?! Nicely done. I hadn't even considered building the hull in two halves. Makes perfect sense now though.:)

Is the armature going to be similar to what was supporting the fuselage pattern?

Did you get my PM?

N
 
Last edited:
You could climb into that raptor, leave your legs sticking out and creep around doing raptor stuff..:lol..maybe that's just me..:wacko

Phil
 
Wow haven't been following for a while, that's a really nice upgrade. I sent a message to Steve, might be interested in one!
 
You must log in or register to reply here.

Similar threads

Rulebreaker
Probe Droid Dispatch Pod 232
Replies
3
Views
450
thibkaji
thibkaji
bwayne64
Galactica Shuttle Parts Maps
2
Replies
35
Views
5,976
bwayne64
bwayne64
Rulebreaker
Revell Imperial Shuttle Retrofit 1/100
Replies
1
Views
1,035
jusdrewit
jusdrewit
Boxcar Bret
Let's Build an Escape Pod!
2
Replies
31
Views
2,874
Studio Kitbash
Studio Kitbash
jusdrewit
Correcting the Revell and Jazware's Micro Galaxy Squadron Imperial Shuttle proportions
4 5 6
Replies
117
Views
21,708
Sym-Cha
Sym-Cha
Back
Top