Limited Run Luke Shared stunt Version Lightsaber ( Run Full )

ALLEY said:
First, I taped off the area above and below the pommel cube rings and roughed up the surface of the pommel cube rings with the lightest steel wool in my bin.

Next, I hit the pommel cubes with repeated coats of aluminum black until the entire pommel cube ring was solid black. After that, I used the steel wool to lighten up the darkness of the pommel cube ring.

After that, I sprayed the pommel cube ring with oven cleaner and let it sit for about 8 minutes.

I then rinsed and cleaned the pommel cubes and removed the painters tape and that was it.

The entire operation took about 1 hour total.
Click to expand...

Thank you for sharing this trick!! I've seen a lot of people trying to replicate this look. This seals it for me, perfect replication!! I wish I had a saber to practice this technique on

Beautiful job matching it to the real piece!!

When u used the oven clean, did u let it stay bubble-ly or did u brush it smooth with a brush?

Sent from my iPhone using Tapatalk
 
OBIWANJALOPY said:
There's already one for sale on the 'bay. (Not me, just for the record.)

Pretty significant markup, which the seller is certainly with in his right to ask for, however.
Click to expand...

Wasting no time! I spent 10 minutes dremmeling the tabs off mine last night and my wife was already on my case about having a new project. I love the saber but I have a feeling I'm not going to get too far on this anytime soon.
 
The problem is that the thickness of the d ring is larger than the diameter of the hole it needs it go into. I needed to use a dremel to make the ring thinner on both sides before trying to attach it to the saber. Frankly it was messy and looked terrible. I'm going to keep searching for a thinner d ring.
 
Sorry to say, I had the same problem. The 3mm hole was simply too small for the D Ring. And since the pommel cubes are so short, there's only so much more material you can cut to enlarge the hole.

I'm hoping that I can find an appropriate sized D Ring from my stash when I return home.

I'm so pleased with the saber otherwise.
 
Anyone still need a clamp card? I made Gerber files for one similar to the sloth furnace card that has hero on one side and Stunt on the other. I'm thinking about ordering some. I think I can get 10 for around $30.
 
CJ2319 said:
Anyone still need a clamp card? I made Gerber files for one similar to the sloth furnace card that has hero on one side and Stunt on the other. I'm thinking about ordering some. I think I can get 10 for around $30.
Click to expand...

I would be in for 2 if you go this route.
 
Would the wannawanga Luke ANH D-ring work or does it use the slightly pointed Obi Wan style one? I can't tell from online pics.
 
The d ring from an ESB style kobold setup would probably be a bit more accurate once installed.

Sent from my SM-J700P using Tapatalk
 
Dann said:
And since the pommel cubes are so short, there's only so much more material you can cut to enlarge the hole.
Click to expand...

I haven't picked my hilt up yet - still at the mailbox, but from the photos posted, it looks like the pommel cubes are close in size to those on the MK1 (Armitage shanks hand wheel), which are noticeably shorter than those of the shared stunt saber props (V2 and V3).

The D-ring I have here with an old Blast-Tech Kobold is 2.7mm which would probably fit nicely - I just can't re-use this one because there's already too much material cut out of it and you'd see that when the D-ring moves to one side on the pommel cube.

I also haven't put the supplied D-ring on my MK1 yet, but I may very well run into the same problem there. The D-ring measures 3.09mm and the hole as best as I can measure is smaller than 3.06mm. Digital calipers in both measurements.
 
Last edited:
With so amount of time at the mailbox you will not have to weather it :)

Pixelpiper said:
I haven't picked my hilt up yet - still at the mailbox, but from the photos posted, it looks like the pommel cubes are close in size to those on the MK1 (Armitage shanks hand wheel), which are noticeably shorter than those of the shared stunt saber props (V2 and V3).

The D-ring I have here with an old Blast-Tech Kobold is 2.7mm which would probably fit nicely - I just can't re-use this one because there's already too much material cut out of it and you'd see that when the D-ring moves to one side on the pommel cube.

I also haven't put the supplied D-ring on my MK1 yet, but I may very well run into the same problem there. The D-ring measures 3.09mm and the hole as best as I can measure is smaller than 3.06mm. Digital calipers in both measurements.
Click to expand...
 
Hey guys, im also currently looking where we can get another dring from. if anyone finds one at a 2.5mm wire thickness please let us know
 
So here is a quck fix until we can find a 2.5mm dring,After measuring the Drings i have left, most of them measure any where from 3.15 / 3.30mm, With a little bit of work you can file down to just under 3mm.


This bar is 3mm Thick

20170406_132601_zpsqhto8rwa.jpg


Fits easy with room in the cube

20170406_132617_zpsbsh7xr2r.jpg


I taped off a section the i can file so the the exposed section will not get scratched.

20170406_132138_zpsalxg2o4j.jpg


Only took about a minute of filing around the ring and got it to size

20170406_132546_zpscyametcb.jpg
 
You must log in or register to reply here.

Similar threads

thd9791
Limited Run Mynock Cave Dagobah Oxygen Tank
2 3 4
Replies
64
Views
5,825
Elevader
Elevader
DaveP
Interest DaveP's V2 and V3 run - 2024
10 11 12
Replies
238
Views
55,062
gobler
gobler
The 48th Ronin
My complete Original Trilogy lightsaber collection (and more)
Replies
15
Views
3,851
Sithslayer
Sithslayer
Dewy
Done / Completed Obi-Wan Kenobi Episode 1 TPM Resin Cast Stunt Lightsaber
4 5 6
Replies
107
Views
16,201
MasterHurd
MasterHurd
eethan
Interest Luke / Vader ANH shared stunt saber kit
14 15 16
Replies
302
Views
37,559
eethan
eethan
Back
Top