E11D DT AIRSOFT PRE MACHINED COMPLETE BUILD KIT WITH GREEBLIES LIMITED RUN !!!!

[Field Marshall]

1. Pre Machined SK sterling airsoft gun , side greeblies windows, pre cut barrel , wire ways in the grip frame and front range finder grommet hole... Full disaasemblies and reassemblies of the grip frame for the correct battery holder and trigeer wiring..
2. one range finder
3. one barrel shroud , pre painted black with heat scoring .. all pin strips and red stickers included ...
4. one Hengstler dt counter with rear vintage rear cover and plug . Pre wired (3) plug leds ready for your install
5. one "Bow Tie " red led greeblie
6. one barrel shroud adapter
7. screen accurate power cylinder
8. one left side window greeblie and yellow led strip
9. one flashlight
10. one flashlight mount and bracket
11. Grip mounted 9 volt battery holder
12. one screen accurate correct collapsible stock .. vintage and hard to find!
13. one rear back cap stock adapter...
14. Shoulder strap with fasteners
15. Pre cut down and ready magazine
16. includes White pin striping and red stickers kit to finish up after you assemble and paint
17. Comes with drill bits and taps to do any finally assembly ..
18. Prebent reformed lower stock
19. All screw and fasteners
20. Free shipping in the USA

LIMITED RUN 20 BUILDS,,, ORDER WILL START SHIPPING MIDDLE TO THE END OF FEB . IF THAT STATUS CHANGES (SOONER OR DELAYS ) A EMAIL NOTIFICATION WILL BE SENT OUT ! MANUFACTURING WILL BEGIN IN FEB SEE OTHER LISTING ON MY EBAY SITE FOR INDIVIDUAL PARTS ebay vmusicstore on eBay

SEE MY OTHER BUILD LISTING FOR SPLIT PAYMENTS ..... ALL ORDERS ARE NON REFUNDABLE !!!!!

Please note this is a serious build and requires assembly , painting, screwing, gluing, drilling, to complete to screen accurate status..

Please post your build on the forums and let me know when you do, i love to see what results you get. Thanks

I will post on my Facebook the preferred commission builders if you need one. i can ship direct to them upon request.

Christopher Fieldmarshal Vandenberghe

 

[OdiWan72]

FINALLY...you know I have been sooo waiting for this.

Ladies and gentlemen, this is the ultimate E11D. Don´t settle with anything less, if you are going for high-end display pieces!!!

Thanks for offering these Chris

 

[xl97]

And room for electronics!

Nice job!

 

[RhinoActual]

How much is the complete kit? Or is it one of those if you have to ask you can't afford it runs?

 

[OdiWan72]

How much is the complete kit? Or is it one of those if you have to ask you can't afford it runs?

^

Hey Rhino...

What you see in the picture is 1200USD, which is a good deal considered all the work that´s involved in making all the individual components of the E11D. Of course you can get a resin or 3D printed one for much less, but this is a high end item, which many will appreciate.

If you´re willing and able to do all/ more work yourself, talk to Chris and maybe save some $

I will be getting one for sure. Have purchased most of the conversion parts from already and was just waiting for the milled S&T receivers!

 

[Field Marshall]

FINALLY...you know I have been sooo waiting for this.

Ladies and gentlemen, this is the ultimate E11D. Don´t settle with anything less, if you are going for high-end display pieces!!!

Thanks for offering these Chris

Yes thankyou
Markus !!!

 

[Field Marshall]

How much is the complete kit? Or is it one of those if you have to ask you can't afford it runs?

I think its affordable if your looking for a real steel build ... This is not a 3d printed build...

 

[Field Marshall]

^

Hey Rhino...

What you see in the picture is 1200USD, which is a good deal considered all the work that´s involved in making all the individual components of the E11D. Of course you can get a resin or 3D printed one for much less, but this is a high end item, which many will appreciate.

If you´re willing and able to do all/ more work yourself, talk to Chris and maybe save some $

I will be getting one for sure. Have purchased most of the conversion parts from already and was just waiting for the milled S&T receivers!

Yees you can save some money if you do the sk sterling yourself ,, all the greeblies are on my site..

 

[Halliwax]

Beautiful...

 

[Field Marshall]

working on 25 e11 counters

 

[DrtyJerzTrooper]

Chris...such an awesome build! Everyone should jump on this. Guys, I have scratch built two of these so far (with Chris’ parts...not part of this run). But I have cut my own Sterling, made MODs, etc. The final product is frickin amazing.There are a few tips and tricks I can share with the group if you are struggling on any install components.

 

[DrtyJerzTrooper]

Here is a quick tip/MOD for builders that you will have to make. I also posted about this in the DT Build group on FB. But...there are two set screws for the folding stock. The right screw (opposite the magazine) has a contact point with the Henglster when you try and mount it. In order to get this to sit flush you will need to grind down the screw. I used a bench top belt sander with 80 grit. Make sure you use some vise grips so that sucker doesn’t fly across the shop and it will get hot...so don’t bare hand this one.

 

[ECOLI]

This might be a stupid question but beside assembly what would be needed to finish the kit? I am assuming some grinding, sanding, gluing, drilling, tapping all pretty standard if doing a blaster etc. However, is any milling/machining needed? Might bump interest if people know what needs to be done on this kit. Its gorgeous and am trying to swing this but didn't want to take this on without knowing what I will need to complete it.

 

[Field Marshall]

This might be a stupid question but beside assembly what would be needed to finish the kit? I am assuming some grinding, sanding, gluing, drilling, tapping all pretty standard if doing a blaster etc. However, is any milling/machining needed? Might bump interest if people know what needs to be done on this kit. Its gorgeous and am trying to swing this but didn't want to take this on without knowing what I will need to complete it.

All machining is done,,,, you will have to wire it up and assemble everything .. painting weathering ect

 

[Field Marshall]

All machining is done,,,, you will have to wire it up and assemble everything .. painting weathering ect QUOTE]

 

[Field Marshall]

Here is a quick tip/MOD for builders that you will have to make. I also posted about this in the DT Build group on FB. But...there are two set screws for the folding stock. The right screw (opposite the magazine) has a contact point with the Henglster when you try and mount it. In order to get this to sit flush you will need to grind down the screw. I used a bench top belt sander with 80 grit. Make sure you use some vise grips so that sucker doesn’t fly across the shop and it will get hot...so don’t bare hand this one.

Not necessary on this kit to change those the real airsoft fasteners are whats on the screen used ones.. that mod is Great on my reg e11 alum kit..

 

[ECOLI]

thanks for the reply, wanted to double check

 

[DrtyJerzTrooper]

Not necessary on this kit to change those the real airsoft fasteners are whats on the screen used ones.. that mod is Great on my reg e11 alum kit..

I didn’t change them. Those are the fasteners that come with the Sterling. Just used a table top belt sander to smooth the one side so the counter sits flush.