ANH Han Solo Blaster scope - dims needed

Don't want to see this ad? Sign up for anRPF Premium Membershiptoday. Support the community. Stop the ads.


Prop Runner

Sr Member
Hey guys.

If one of you has a REAL Hensoldt-Wetzlar DAILYT3X scope or measurements taken from one, I'd be grateful if you could e-mail me the mm dimensions below:

HW_DIALYT3X_dims.JPG


HW_DIALYT3X_dims_2.JPG


If you have a set of calipers (preferably in mm), please be as exact as you can.

Note: dimensions 1, 2, 3, 6, and 14 are from the inner edges of the scope bell retention rings, in case it's not clear in the photo.

My e-mail is proprunner@aol.com

Thanks in advance. :)

- Gabe
 

Don't want to see this ad? Sign up for anRPF Premium Membershiptoday. Support the community. Stop the ads.

mgoob

Sr Member
RPF PREMIUM MEMBER
the front & rear brass rings are 1/16" thick (from front of scope to end of ring)

The inner diameter of the rear lens is 1"

the screws are 2.5mm in diameter

That's what I know off the top of my head
(I have one, but the W/E knob is a repro)
 

spinner 44

Well-Known Member
Originally posted by Prop Runner@Jan 7 2006, 06:28 AM
*BUMP* for the EU crew and the weekend shift :)
[snapback]1152950[/snapback]​


Gabe,

I have a resin cast of a original H&W (correct model). I know it might be small shrinking due to casting, but I'll post your requested measures as soon as I get home after work. I have Mauser steel caliper, so at leats the measure will be precise (in mm).

If you think the casted scope is not a very reliable source, just tell me so :p
 

Don't want to see this ad? Sign up for anRPF Premium Membershiptoday. Support the community. Stop the ads.

Prop Runner

Sr Member
Originally posted by spinner 44@Jan 7 2006, 12:49 AM
Gabe,

I have a resin cast of a original H&W (correct model). I know it might be small shrinking due to casting, but I'll post your requested measures as soon as I get home after work. I have Mauser steel caliper, so at leats the measure will be precise (in mm).

If you think the casted scope is not a very reliable source, just tell me so  :p
[snapback]1152989[/snapback]​
Muchas gracias, amigo. :D

Measurements in mm are exactly what I need, and somehow it's appropriate that a Mauser caliper will be used to measure the casting. ;)

I look forward to your post or e-mail,

- Gabe
 

Got Maul

Official Licensee
gabe, do you still need these numbers ? I could pull them off mine and I am going to a friends place that HAS calipers...
 

Prop Runner

Sr Member
Originally posted by Got Maul@Jan 7 2006, 08:12 AM
gabe, do you still need these numbers ? I could pull them off mine and I am going to a friends place that HAS calipers...
[snapback]1153097[/snapback]​
Yes, Jose, please do - since Sergios's scope is a 1st-gen resin cast, it would help to validate his measurements off a metal one in case there was some shrinkage.

Sergio: got your e-mail, thanks for being so thorough. :) :thumbsup

- Gabe
 
This thread is more than 15 years old.

Your message may be considered spam for the following reasons:

  1. Your new thread title is very short, and likely is unhelpful.
  2. Your reply is very short and likely does not add anything to the thread.
  3. Your reply is very long and likely does not add anything to the thread.
  4. It is very likely that it does not need any further discussion and thus bumping it serves no purpose.
  5. Your message is mostly quotes or spoilers.
  6. Your reply has occurred very quickly after a previous reply and likely does not add anything to the thread.
  7. This thread is locked.

Don't want to see this ad? Sign up for anRPF Premium Membershiptoday. Support the community. Stop the ads.

Top