Yes please!
Yes!!!
Wellllllllll OK then.
View attachment 1049295
RPK Customs Gen 4 V2 weathered and installed with Proffieboard/Neopixel by TheErrantVenture on Etsy.
View attachment 1049303
Some Dremel dings under the pommel. (Sound is vented via the Graflex clamp holes instead.)
View attachment 1049308
View attachment 1049313
View attachment 1049321
View attachment 1049323
View attachment 1049325
Started off with 4 ROTJ Luke fonts, two lime-green and two true green blade colors (each pair has a static and flicker mode).
Can't wait to take this bad boy out tomorrow night.
Wellllllllll OK then.
View attachment 1049295
RPK Customs Gen 4 V2 weathered and installed with Proffieboard/Neopixel by TheErrantVenture on Etsy.
View attachment 1049303
Some Dremel dings under the pommel. (Sound is vented via the Graflex clamp holes instead.)
View attachment 1049308
View attachment 1049313
View attachment 1049321
View attachment 1049323
View attachment 1049325
Started off with 4 ROTJ Luke fonts, two lime-green and two true green blade colors (each pair has a static and flicker mode).
Can't wait to take this bad boy out tomorrow night.
Love you five thin neck collection. This is my goal! Have three so far but a lot of work ahead!I wanted to start a general thin-neck saber appreciation thread since I think the design is so cool! The idea is that folks can post pictures and discuss their own replicas, other sabersmith's creations, the screen used sabers, and other non-canon designs. Anything goes as long as it's thin-neck oriented.
To start, here are some pics of my personal collection.
View attachment 1255723
From left to right we have:
Roman's Obi-Wan hero in the Tattooine configuration (upside down pommel cubes, both transistors have washers, the brass above the windvane is tarnished and not shiny)
Starkiller unibody V2 painted up as an ANH-era Obi-Wan stunt. Roman's empire replica clamp with Wannawanga bubbles and lever.
Starkiller 3 piece V2 with Roman clamp and d ring. I got the card on a whim from some ebay seller that I can't remember.
Spirit of OB1 shared stunt. The clamp is a logoless replica from TCSS, but the logo is covered with tape so it doesn't matter.
Nicksdad ROTJ hero. The neck is painted dirty brass (which I strongly feel is more accurate) as opposed to copper.
View attachment 1255724
On top is a Roman's Empire Obi ROTS saber. The TPM Obi (Korbanth) and Qui-Gon (one replicas) get honorable mentions because they have elements of the thin-neck style.
One non-canon design that I absolutely love is the Big Boy by Turkish company Saberkraft. It's a really cool, stylized take on the thin-neck motif
View attachment 1255725View attachment 1255726
I don't own one, but I saw a vid by Shameem of one of his electronics installs and I thought it was just so neat.
I'm also intrigued by the upcoming Korbanth LS6 design with the Crystal chamber reveal.
View attachment 1255727
The saber has elements of the hero, V2, and shared stunt. I think it could be a cool basis for an idealized hybrid saber. For some reason, even though it's not very accurate to any one particular version, I really want to get one!
Sent from my SM-J700P using Tapatalk
I tried to capture what I see in hand. I suck at taking pictures and lighting. Halliwax is the best! Can’t thank him enough. It’s all there. I just can’t display it in a photo. Actual setup I had for reference. Love this hilt!
View attachment 1255811View attachment 1255810
Question about your 'custom' Neopixel blade?
What custom LEDS are you using?
The "Neopixel" led are really WS2812(B?).. and have an integrated/on-board chip.. and requires a microcontroller to run.
Just wanna make sure you dont waste any more or time.
Side note:
Is that a 1in blade?
You can make a decent v2 if you mod all the parts on the rightgreat topic, here is my collection so far, the last on the right is a mashup of saberforge parts , the other pic is technically notthin neck, but derived