newmagrathea
Sr Member
What is the cost of the plaques? I'll need 2, Han Hoth and Luke.
I don't care if it says Bespin or not.
I don't care if it says Bespin or not.
-
Welcome to the Project Runs Forum!
This forum is intended for interest gauging and active runs. Due to the transient nature of this forum, please keep all research and ongoing discussion in one of our main forums so your information is not lost.
Only Premium Members can start a new run.
Limited Run RUN CLOSED * DL-44 ESB Blaster Machined Parts Set * RUN CLOSED
- Thread starter Boba Debt
- Start date
This with the updated text.
Boba Debt
Master Member
BRASS PISTON DETAILS
My shop called with some questions about the pistons
All of the pistons will need the following processes:
There is an additional detail that we have not discussed.
At the center seam line there is some sort of hardware that appears to be part od the pistons. We can accomplish this 2 ways.
Modifying the hardware with a machining process could be very costly so most people that would want to achieve this look by doing that will modify the hardware by hand. It will not be easy nor consistent.
Machining the pockets into the side will obviously add to the cost but I don't think it will be that much. If someone were to ask ME to modify the hardware for them I would probably charge $10 because this will be a pain and time consuming. I seriously doubt these 2 pockets will add even half of the much to the cost but you never know.
ANYWAY, lets discuss this.
My shop called with some questions about the pistons
All of the pistons will need the following processes:
- The spru machined of the back at the seam line
- The 2 holes will be drilled though
- The surface of the holes (where the phillips screw contacts) will get a very light spot face to clean it up
There is an additional detail that we have not discussed.
At the center seam line there is some sort of hardware that appears to be part od the pistons. We can accomplish this 2 ways.
- Modify a screw or bolt so that it sits beside the pistons to create the look
- Machine a counter bored "pocket" into each side of the piston so the screw or bolt can be left in tact
Modifying the hardware with a machining process could be very costly so most people that would want to achieve this look by doing that will modify the hardware by hand. It will not be easy nor consistent.
Machining the pockets into the side will obviously add to the cost but I don't think it will be that much. If someone were to ask ME to modify the hardware for them I would probably charge $10 because this will be a pain and time consuming. I seriously doubt these 2 pockets will add even half of the much to the cost but you never know.
ANYWAY, lets discuss this.
wh1plash
Member
If the machinists can do this at a reasonable price <$10 as you mentioned I'm happy to add that process.
... plaques look good to me btw
Agreed on both items.
Mara Jade's Father
Master Member
I like the machine tabs. Something totally different from previous replicas out there.
Ok it looks like these are the finals. I'll have Boba Debt send out an email with ordering info shortly.
newmagrathea
Sr Member
I think I'd like it machined to get the right look. I don't have the tools to do it myself.
looks awesome!!
Handy Solo
Active Member
Whoops! I didn't realize the scope bolts were a part of the scope invoice. Is there any chance I can still get in on a set of standard scope bolts?
Sorry, I'm late to comment on the plaques too. They look good. Anybody think there should be a colon or something else to break up the text at the bottom?
Sorry, I'm late to comment on the plaques too. They look good. Anybody think there should be a colon or something else to break up the text at the bottom?
now you have me worried.. did i order scope bolts as well?!
i just sent boba a PM. im nervous now, god i hope your right
Handy Solo
Active Member
I didn't mean to alarm anyone. I thought they would be in the hardware invoice at the end as well. However, in the first post, it lists the scope bolts as being part of the scope invoice
¯\_(ツ)_/¯
¯\_(ツ)_/¯
Boba Debt
Master Member
Sorry I missed this situation.
The scope bolts will be invoiced with the Scope Machining Process along with the machined Light Sockets and if the deluxe machining is selected the lens rings and glass lenses.
I know this thread and project have been very long but I will make sure that the group does not miss any important info by both posting it here and then including it in an email.
The scope bolts will be invoiced with the Scope Machining Process along with the machined Light Sockets and if the deluxe machining is selected the lens rings and glass lenses.
I know this thread and project have been very long but I will make sure that the group does not miss any important info by both posting it here and then including it in an email.
Similar threads
