ROTS Vader Mask Interior

[Darthmagpie]

Thought I would bump this guy up. Any new parts identified? Any progress or finished mask pics?

 

[Darthmagpie]

Anything here guys? Looks like the pic in the first post fell-off. Should I put it back up? anyone have any finished or WIP masks?

 

[admiral mick]

yes please put the pic back up

 

[Anakin Starkiller]

Does anyone have the pics that were posted here on the first page?

Thanks

Dan Stokes
DDStokes@aol.com

 

[Darthmagpie]

I put the first pic back up. Would be great to get the list filled in.

 

[artoo77]

Thought I'd jump in and help...though I can't remember everything.


1-Custom Laser cut Part
2-As with #3 below, the base is a lasercut part, but I believe I used some EMA parts for the right angle connection. I'd nee to see higher-rez pics
3-Custom Laser cut Part
4-Hard drive reader fingers;Model: western digital 102ba
5-Hard drive reader arms (Model?) (not confirmed)
6-
7-Toolbox drawer liner
8-Hard drive reader fingers; IBM 9 GB SCSI
9-Hard drive reader arms (Model?) (not confirmed)
10-Tamiya 1/35 scale 20mm Flackvierling 38 (part #2)
11-
12-Custom Laser cut Part
13-
14-Tank treads;tamiya panzer kampfwagen iv(not confirmed)
15-
16-Molex pins(Confirmed)
17-Custom Laser cut Part
18-Tamiya 1/35 scale 20mm Flackvierling 38 (part #11)
19-Tamiya 1/35 scale 20mm Flackvierling 38 (part #1)
20-Tamiya 1/35 scale 20mm Flackvierling 38 (part #8)
21-Leaf Switch
22-Wire loom (No, but I can't remember what it is)
23- Tamiya 1/35 scale 20mm Flackvierling 38 (part #?)


The metal cabling is Hosmer cable housing of different sizes, and there was some stainless steel as well as some brass.

--Don Bies

Hello all,

 

[jme3]

Sure wish you could do this for the ROTJ version...! :cry

Thought I'd jump in and help...though I can't remember everything.


1-Custom Laser cut Part
2-As with #3 below, the base is a lasercut part, but I believe I used some EMA parts for the right angle connection. I'd nee to see higher-rez pics
3-Custom Laser cut Part
4-Hard drive reader fingers;Model: western digital 102ba
5-Hard drive reader arms (Model?) (not confirmed)
6-
7-Toolbox drawer liner
8-Hard drive reader fingers; IBM 9 GB SCSI
9-Hard drive reader arms (Model?) (not confirmed)
10-Tamiya 1/35 scale 20mm Flackvierling 38 (part #2)
11-
12-Custom Laser cut Part
13-
14-Tank treads;tamiya panzer kampfwagen iv(not confirmed)
15-
16-Molex pins(Confirmed)
17-Custom Laser cut Part
18-Tamiya 1/35 scale 20mm Flackvierling 38 (part #11)
19-Tamiya 1/35 scale 20mm Flackvierling 38 (part #1)
20-Tamiya 1/35 scale 20mm Flackvierling 38 (part #8)
21-Leaf Switch
22-Wire loom (No, but I can't remember what it is)
23- Tamiya 1/35 scale 20mm Flackvierling 38 (part #?)


The metal cabling is Hosmer cable housing of different sizes, and there was some stainless steel as well as some brass.

--Don Bies

 

[Darthmagpie]

Don, Thank you so much for you input!!!!!! Here is a higher res pic of the area you requested. any help in this area is most appreciated. Can you expand on what "EMA" is? It appears as a rule of thumb based your input that the copper colored pieces are all custom lazer cut, is this true?

Thanks again, Ben

 

[Darthmagpie]

bump, incase Don is around

 

[Darthmagpie]

Maybe I have another piece identified:
1/35 Kampfpanzer Leopard

But at the same time, I am not sure:confused

I really think that that part and this part are from the same kit, why? I don't know just from looking through tank kits I get the feeling this other part is the front frame/suspension from some kit that is a tank and the little hub might be a common looking part that is from THAT tank kit.

I also have a feeling that what I have labeled key part is the key to some further success here. I really think that it is half of a rear axle gear case but the only place i know to look is studioscale.com and i don't see it there.
Ben

Thanks Wackychimp

 

[Darthmagpie]

opinions?

 

[Darthmagpie]

just trying to generate a renewed interest with a bump.

 

[Lord DarkFinger]

I know this forum is old but I was wondering if anyone is currently selling these parts in a kit form?

 

[21bdp21]

#22 is the actual HDD suspension not a wire loom the entire nose bridge came out of a HDD. How I know I am currently working at a HDD suspension manufacturer.
http://cdn2.goughlui.com/wp-content/uploads/2013/03/DSC_0029.jpg
View attachment 556959There is a suspension assembly in this photo not the one in the mask, but it shows that it isn't 4 different parts