Omarbou1's IM mark VII pep files - Chest uploaded !
- Thread starter omarbou1
- Start date
coffeehedake
Active Member
Re: iron man mark 7 few pep files-unfolder needed for V2 HELMET FILE
So, just checking, your head was 235MM (23.5CM) Tall, and you set the scale height to 278MM, and it fit well?
I just (attempted) to measure my own head from crown of the skull to bottom of the chin was around 200MM (20CM).
If so, that gives me a conversion ratio of ~ 1.83 (278/235)
So, 200MM * ~1.83 = ~237MM for the height of my helmet at the same ratio. I think. My math fu is weak.
Going to have the girlfriend try to more accurately measure my head... I used the two marks on a wall method.
So, just checking, your head was 235MM (23.5CM) Tall, and you set the scale height to 278MM, and it fit well?
I just (attempted) to measure my own head from crown of the skull to bottom of the chin was around 200MM (20CM).
If so, that gives me a conversion ratio of ~ 1.83 (278/235)
So, 200MM * ~1.83 = ~237MM for the height of my helmet at the same ratio. I think. My math fu is weak.
Going to have the girlfriend try to more accurately measure my head... I used the two marks on a wall method.
coffeehedake
Active Member
Re: iron man mark VII helmet V2 by omarbou1! links in first post !
D'oh! Ok, thanks for that, I wasn't sure if you were doing height in CM, or circumference in inches, the conversion threw me a bit.
Sent from my iPhone using Tapatalk
D'oh! Ok, thanks for that, I wasn't sure if you were doing height in CM, or circumference in inches, the conversion threw me a bit.
Sent from my iPhone using Tapatalk
coffeehedake
Active Member
Re: iron man mark VII helmet V2 by omarbou1! links in first post !
Ok... Measured my head circumference and got 22 1/4"
So...
My 22 1/4" head divided by your 23 1/2" head is a scale ratio of ~0.95.
~0.95 * your height of 278 is ~236 for my height... if my math is right. Which it usually isn't.
So a height of 236 should be right? Sorry for asking a noob question like this, I've never gotten scaling right. *sigh*
I think I might be missing where or how you got the 278 part.
Ok... Measured my head circumference and got 22 1/4"
So...
My 22 1/4" head divided by your 23 1/2" head is a scale ratio of ~0.95.
~0.95 * your height of 278 is ~236 for my height... if my math is right. Which it usually isn't.
So a height of 236 should be right? Sorry for asking a noob question like this, I've never gotten scaling right. *sigh*
I think I might be missing where or how you got the 278 part.
Re: iron man mark VII helmet V2 by omarbou1! links in first post !
Hehe ok i made my first helmet with the default scale it it turned out too small for me .... but i made 278 just by guessi g what size would it be ok with servos and all
With your measurment i would set the height to260 or even the default scale! anyway i made like 5 helmet before beeing pleased with the result so yeah 260-262 would be enough
Hehe ok i made my first helmet with the default scale it it turned out too small for me .... but i made 278 just by guessi g what size would it be ok with servos and all
With your measurment i would set the height to260 or even the default scale! anyway i made like 5 helmet before beeing pleased with the result so yeah 260-262 would be enough
coffeehedake
Active Member
Re: iron man mark VII helmet V2 by omarbou1! links in first post !
Awesome, thanks so much omarbou1! I'll give it a shot as soon as I have foam to work with.
Thank you for the help and the great model!
Awesome, thanks so much omarbou1! I'll give it a shot as soon as I have foam to work with.
Thank you for the help and the great model!
typewriter
Active Member
Re: iron man mark VII helmet V2 by omarbou1! links in first post !
Hey omarbou!! I just finished pepping and resining your v2 helm!
Hey omarbou!! I just finished pepping and resining your v2 helm!
typewriter
Active Member
Re: iron man mark VII helmet V2 by omarbou1! links in first post !
I'm glad you like it! I hope I did well on it, made lots of supports so it didnt warp even a bit when i resined it I worked on it as soon as you told me there was already a v2 file hahaha, so I like it very very much! Thanks omarbou!
That's awesome !!
I love seeing progress pics!
Especially qhen its from my file
Did you like building it ?
Keep building
I'm glad you like it! I hope I did well on it, made lots of supports so it didnt warp even a bit when i resined it
I worked on it as soon as you told me there was already a v2 file hahaha, so I like it very very much! Thanks omarbou!Re: iron man mark VII helmet V2 by omarbou1! links in first post !
Your welcome !
Here is a hint: put two coats of resin before fibrglassing
And put at least 2 coats of fiberglass
I assure you, you dont want any weak spot when it comes to bondo !!
Oh and speaking about bondo, applr bondo and work only part by pasts to keep things symetrical
Also put thin coats and sand gradually
60 grit then fill low spot, 90grit, primer, fill low spot ,120 grit .. fill low spot then i use 320 grit
put coat of primer an then i wet sand with 600 80 1200 grit so it perfect
Your welcome !
Here is a hint: put two coats of resin before fibrglassing
And put at least 2 coats of fiberglass
I assure you, you dont want any weak spot when it comes to bondo !!
Oh and speaking about bondo, applr bondo and work only part by pasts to keep things symetrical
Also put thin coats and sand gradually
60 grit then fill low spot, 90grit, primer, fill low spot ,120 grit .. fill low spot then i use 320 grit
put coat of primer an then i wet sand with 600 80 1200 grit so it perfect
Re: Omarbou1's IM mark VII pep files- lower forearm w/ removable missile pod added !
coming soon !!!
streetsoul is unfolding them as we talk !
i made two biceps verisons !
1 symmetric : for those who planned on molding the you will make one single mold
1 asymetric ... well for the others XD
i am currently modelling the neck !!
coming soon !!!
streetsoul is unfolding them as we talk !
i made two biceps verisons !
1 symmetric : for those who planned on molding the you will make one single mold
1 asymetric ... well for the others XD
i am currently modelling the neck !!
Madosheet
Active Member
Re: Omarbou1's IM mark VII pep files- COMING SOON PICTURES LAST PAGE
Is that a new MK42 I see? Will you be releasing that as well?
I already have 2 different MK42's pepped, but the more the merrier xD especially if each joins differently - yours is at the jaw?
But awesome work, especially on the two different arms!
Is that a new MK42 I see? Will you be releasing that as well?
I already have 2 different MK42's pepped, but the more the merrier xD especially if each joins differently - yours is at the jaw?
But awesome work, especially on the two different arms!
Re: Omarbou1's IM mark VII pep files- COMING SOON PICTURES LAST PAGE
yes it is !!!
i made the jaw separate to be easier to split and more accurate !
i really put myself at work on this one to be one of th most accurate !
it will be released as soon as streetsoul finish unfold it
thanks for the compliment !!!
yes it is !!!
i made the jaw separate to be easier to split and more accurate !
i really put myself at work on this one to be one of th most accurate !
it will be released as soon as streetsoul finish unfold it
thanks for the compliment !!!
kenujio
Well-Known Member
Re: Omarbou1's IM mark VII pep files- lower forearm w/ removable missile pod added !
WOW¡¡¡¡¡¡¡ MK 42 helmt? and mk 7 armor?thumbsup
WOW¡¡¡¡¡¡¡ MK 42 helmt? and mk 7 armor?
thumbsup
streetsoul
Sr Member
Re: Omarbou1's IM mark VII pep files- COMING SOON PICTURES LAST PAGE
The mk42 helmet will be my top priority well theses re all my top priority I'll get them done asap people
The mk42 helmet will be my top priority well theses re all my top priority I'll get them done asap people
Re: Omarbou1's IM mark VII pep files- lower forearm w/ removable missile pod added !
yes it isWOW¡¡¡¡¡¡¡ MK 42 helmt? and mk 7 armor?
Re: Omarbou1's IM mark VII pep files- COMING SOON PICTURES LAST PAGE
Really good job on your files dude!
I'll give a try to the forearms.
edit: just checked the length with reference pictures, isn't it a bit short? If I scale it from elbow to before the wrist, circumference is a bit too large. I'm 5'10'' so I need more or less 27-28 cm (11 inches) long. But then it's too wide. There may be the same issue as in darkside's files. Only a constructive critics...excellent work nonetheless! Keep up your nice work, I'm no good in modelling ^^
Really good job on your files dude!
I'll give a try to the forearms.
edit: just checked the length with reference pictures, isn't it a bit short? If I scale it from elbow to before the wrist, circumference is a bit too large. I'm 5'10'' so I need more or less 27-28 cm (11 inches) long. But then it's too wide. There may be the same issue as in darkside's files. Only a constructive critics...excellent work nonetheless! Keep up your nice work, I'm no good in modelling ^^
Last edited:
Re: Omarbou1's IM mark VII pep files- COMING SOON PICTURES LAST PAGE
well here is the v2 maybe its fixed ! i didn't get my attention into this !
Ironman MarkVII forearm V2 modeled by omarbou1 unfolded by streetsoul - Download - 4shared
also you have to take the upper forearm in consideration
anyway if its still too wide let me know and i'll fix it !
oh thanks !
well here is the v2 maybe its fixed ! i didn't get my attention into this !
Ironman MarkVII forearm V2 modeled by omarbou1 unfolded by streetsoul - Download - 4shared
also you have to take the upper forearm in consideration
anyway if its still too wide let me know and i'll fix it !
Similar threads
