Unlimited Run Hasbro Millennium Falcon 3D printed upgrades

FZ6 · Feb 8, 2015

FZ6 · Feb 9, 2015

Just to let you know about the quality of these parts.

My upgrades have been used by Marc Elkins to modify four Hasbro Falcons.

You can see my parts featured on the Modeler Magic article:

http://www.modelermagic.com/?p=65981

Just watch the photos of my upgrades.

Many thanks for watching

animefan · Feb 9, 2015

Wow great work you have done here! These look like incredible upgrades!

FZ6 · Feb 10, 2015

animefan said:
Wow great work you have done here! These look like incredible upgrades!

Many thanks for your comments Animefan!!

FZ6 · Feb 11, 2015

Another reputed artist that is using my Hasbro upgrade parts is Randy Cooper.

You can see my parts on his Facebook page!

On the image you can see my cockpit parts, upper and back wall, cockpit and cone.

Many thanks for watching!

Nils · Feb 11, 2015

Looking great! Do you have a kit price (every part included)?

FZ6 · Feb 11, 2015

Nils said:
Looking great! Do you have a kit price (every part included)?

Hi Nils.

Many thanks for your interest!

For the 3D printed parts, they're sold individually, but can be ordered all at once, only a part or only a few. As you want.

As the parts are 3D printed individually for you when you order them, you can make a purchase whenever you want, and the amount you want. So you can plan to buy the parts gradually on line. In 15 days -or less- the parts are at your door.

On other hand, me and Mike Salzo we are preparing too a resin kit based on these 3D printed high detailed parts, and it will be available very soon. I will post here.

If you have further questions don't hesitate to get back to me.
Many thanks again for your interest.

Best

Nils · Feb 11, 2015

Thanks for the info!

FZ6 · Feb 12, 2015

You can see an example of the quality detail of my sidewalls.

All the upgrades that I've designed are totally accurate with the 32" Falcon. So you can convert the Hasbro on a Studio Scale model. Every little detail of the original studio filming model has been reproduced on my parts.

In fact, my cockpit has more detail than the Studio Scale Falcon...

You can have a Studio Scale Falcon for a fraction of the cost of an original Studio Scale Falcon. People is asking $4.000 bucks for one SS model! You can have one for less than $700.

Many thanks for watching!

FZ6 · Feb 13, 2015

To design the Hasbro sidewalls upgrades, I've used the original shots of the 32" studio filming Falcon, and the measurements taken for my friend Jedi Dade on his Studio Scale Master Replica Falcon.
With his help and his very accurate measurements, I've designed the sidewalls.

So the sidewalls are a real replica of the original falcon. Nobody is offering such accurized parts for the Hasbro.

Many thanks for watching!!!

FZ6 · Feb 14, 2015

The back wall of the cabin has been designed following the original 1:1 studio filming model.
On the back wall I've designed approximately 150 holes, so it's fiber optics ready!!!

On this image, courtesy of Marc Elkins -shown on Modeler Magic (many thanks Kuhn!)- http://www.modelermagic.com/?p=65981 you can see the size and the high detail.

Many thanks for watching!

FZ6 · Feb 15, 2015

Josh, one of the guys here at RPF, has published a shot of my back wall with fiber optics lighting. Thanks Josh!

You can put more than 300 fiber optics wires on my cabin walls!!!!

Are you ready for this? Are you skilled enough for this? :cool

Many thanks for watching!

FZ6 · Feb 16, 2015

The laser cannons, the quad laser, have the same design than the original cannons seen on the studio filming model.

Of course, these cannons have more detail and better proportions than the Hasbro cannons.

A good upgrade, a must have.

Thanks to Leyrich for the shot!

Many thanks for watching!

FZ6 · Feb 17, 2015

The upgrades list is growing.

I've just added a new cabin cone with built in side cockpit consoles. The little detail to have an interesting cockpit.

https://www.shapeways.com/product/RVSTR8R8S?li=shop-results&optionId=55887660

Many thanks for watching!!

FZ6 · Feb 18, 2015

The quad laser upgrade looks nice!!!

A very big improvement over the standard Hasbro cannons!

I've designed the cannons following the original studio filming model. And the result I think that's quite good!

Many thanks to Leyrich form the shot.

MILLENNIUM FALCON HASBRO LASERS hand.JPG

Many thanks for watching!

FZ6 · Feb 19, 2015

Here you can see an astronaut showing you my turret well window. As you probably know, the turret window well of the Hasbro is blind. So you can have a new window just cutting the old one, and replacing it with my very detailed window.

The window fits perfectly the size of the Hasbro kit. It's just plug&play, as you can see on the image -courtesy of Leyrich! Thanks!-.

I've designed the window following closely the original part of the studio filming model.

If you want to check all my Hasbro upgrades, just visit:

https://www.shapeways.com/shops/308bits?section=Falcon+HSBRO&s=0

MILLENNIUM FALCON HASBRO TURRET WINDOW.JPG

Many thanks for watching!

FZ6 · Feb 20, 2015

Another shot to see the turret well window.

You can see also the mandibles inner side walls, highly detailed, a replica of the ones seen on the 32" studio filming Falcon.

MILLENNIUM FALCON HASBRO MANDIBLES SIDEWALLS TURRET WINDOW.JPG

Many thanks for watching -and many thanks to Leyrich for the shot!-

FZ6 · Feb 22, 2015

A photo worth more than a million words...

My 3D printed laser cannons on the left. The Hasbro ones, at the right..

Many thanks to Leyrich for the shots!

And many thanks for watching!

FZ6 · Feb 23, 2015

And this is the last part I've designed. The laser cannon yoke support, with more detail and with the missing overhang on the standard part.

The link:

https://www.shapeways.com/product/X2YAEU6A3?li=shop-results&optionId=55932597

Many thanks for watching!

FZ6 · Feb 24, 2015

More details, this time from the inner mandibles sidewall parts.

The inner part has been designed following the original 32 incher. A quasi perfect replica.

Note that the two parts are different, not a simpler mirrored part. Each side is different. Of course, thanks to Leyrich for the shots.

MILLENNIUM FALCON HASBRO INNER MANDIBLES SIDEWALL.JPG

Many thanks for watching!

Welcome to the Project Runs Forum!

Unlimited Run Hasbro Millennium Falcon 3D printed upgrades

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Sr Member

Similar threads