Unlimited Run De Agostini Millennium Falcon 3D printed upgrades

FZ6

Sr Member
RPF PREMIUM MEMBER
Hello again!

More 3D printed parts, but no for the Hasbro or the MPC Falcon this time.

Now I've started working on the new De Agostini Millennium Falcon upgrades! It's huge!

These are by now the available 3D printed upgrades:

-Dejarik table
-Hall navigator seat
-3 sets of hall bits seen on the original ANH (barrels, cans, rugged boxes...)
-Laser cannon
-Laser cannon yoke
-Laser belly turret

More to come!!!

MILLENNIUM FALCON DEAGO HALL BITS RENDER.jpg MILLENNIUM FALCON DEAGO HALL BITS.jpg

Many thanks for watching!!!

Oooppsss!!! Missing link:

DeAgo section:

https://www.shapeways.com/shops/308bits?section=Falcon+DeAgo&s=0

Dejarik table:

https://www.shapeways.com/product/F7UUSWLN3?li=shop-results&optionId=55961300

Nav console chair:

https://www.shapeways.com/product/26CR5P5VL?li=shop-results&optionId=55961597

Hall bits:

https://www.shapeways.com/product/3B5LABLNN?li=shop-results&optionId=55962559
 
Last edited:

FZ6

Sr Member
RPF PREMIUM MEMBER
The Dejarik table...

A very close replica of the original one, with all the little details. I've designed too the panels on top, for easy painting.

MILLENNIUM FALCON DEAGO DEJARIK.jpg

And the links

DeAgo section:

https://www.shapeways.com/shops/308bits?section=Falcon+DeAgo&s=0

Dejarik table:

https://www.shapeways.com/product/F7UUSWLN3?li=shop-results&optionId=55961300

Nav console chair:

https://www.shapeways.com/product/26CR5P5VL?li=shop-results&optionId=55961597

Hall bits:

https://www.shapeways.com/product/3B5LABLNN?li=shop-results&optionId=55962559
 

Ollois

Active Member
Really need to get your replacement nose cone, when do you think it will be available and will I be able to use the existing De Agostini Cockpit Interior?
So glad you are doing this!
 

FZ6

Sr Member
RPF PREMIUM MEMBER
Really need to get your replacement nose cone, when do you think it will be available and will I be able to use the existing De Agostini Cockpit Interior?
So glad you are doing this!
Hi Ollois!

I've started designing the cockpit. It will have side consoles too.

About the cone, I will design it too. As soon as I get the measurements, I will start working on it. Cockpit and cone will be released together. I need both to design each one.

Many thanks for your interest!
 

FZ6

Sr Member
RPF PREMIUM MEMBER
I can send you the 2 cone halves and linking piece if you need them urgently?
Thanks Ollois!

Trimotor will give me the measurements I need. I've posted him on the De Agostini thread on the studio scale section.

By the way, it will be useful to have the measurements of the hall floor -I haven't received yet this issue-. The size of the tiles and the pits grille -length and width-. I've posted at my shop the pits grille on 41.1 x 41.1 mm. I think that's the good size. Check it!

A big thanks!
 

Ollois

Active Member
Hopefully this will help...
image.jpg
Small Square Tiles are 21mm
Pit Grill is 36mm Square with 19.5mm short edge to form angles
Main Floor is 162mm x 140mm with extra 3mm 'lip'
The cut outs on the lip have non linear measurements along edge of lip
Corner cut out is 47.5mm x 30mm
 
Last edited:

FZ6

Sr Member
RPF PREMIUM MEMBER
Hopefully this will help...

Small Square Tiles are 21mm
Pit Grill is 36mm Square with 19.5mm short edge to form angles
Main Floor is 162mm x 140mm with extra 3mm 'lip'
The cut outs on the lip have non linear measurements along edge of lip
Corner cut out is 47.5mm x 30mm
Excellent work!!!

Many thanks!!!

Going to work a little bit more now... :D
 

Jedi Dade

Sr Member
You do of course realize that the Studio Scale parts are also good for Deagostini right :D.

Thanks for this Tony!

Jedi Dade
 
  • Like
Reactions: FZ6

FZ6

Sr Member
RPF PREMIUM MEMBER
What's wrong with the De Agostini cone?

I think the De Agostini cockpit is real nice but I can tell where Shapeways-Master-Tony can make improvements but what about the cone??

Tom
I'm thinking the same Tom.

Well... I will try my best!!!

- - - Updated - - -

floor tiles are actually rectangular and are 21mm x 17.5mm
Nice!!!

Thanks

- - - Updated - - -

You do of course realize that the Studio Scale parts are also good for Deagostini right :D.

Thanks for this Tony!

Jedi Dade
Yes, I know that!

Despite the scale is the same the parts have different sizes... Small differences. it's curious that you can't apply the same "scale rule" for the parts... All the parts have to be remodelled again for each kit.
 

FZ6

Sr Member
RPF PREMIUM MEMBER
And more grilles for the hall.

Of course, a very close replica of the original ones. They're 21 x 17 x 1 mm.
I've made a set of 15 tiles.

http://shpws.me/GaFC


MILLENNIUM FALCON DEAGO HALL GRILLE TILE RENDER.jpg

Many thanks for watching!!
 
Last edited:

FZ6

Sr Member
RPF PREMIUM MEMBER
I've just released a new part!!!

Is the hall bits 4th, that includes the stood where Obi Wan was seated on the ANH, close to the nav station, a tool tray, something like two gas bottles from a soldering kit, and the tool roll. All these parts are designed inspired on the original bits seen on the ANH and ESB. Are very close to the original bits. Do you remember them when Han was repairing the Falcon on the asteroids field?

Just take a look:

http://shpws.me/Gtcc

MILLENNIUM FALCON DEAGO HALL BITS 4 CHAIR TOOLS.jpg

Many thanks for watching!!!
 

Tom1971

Sr Member
I've just released a new part!!!

Is the hall bits 4th, that includes the stood where Obi Wan was seated on the ANH, close to the nav station, a tool tray, something like two gas bottles from a soldering kit, and the tool roll. All these parts are designed inspired on the original bits seen on the ANH and ESB. Are very close to the original bits. Do you remember them when Han was repairing the Falcon on the asteroids field?

Just take a look:

http://shpws.me/Gtcc

View attachment 447757

Many thanks for watching!!!

I am afraid to ask because I know you will say yes and thus it will cost me more money but would you be able to upsize all the interior bits, storage barrels, boxes, etc. for the 3 3/4 inch BMF??? It would make an awesome addition to the full BMF Toy to go with the figures.
 
Top