Done / Completed Greedo Blaster DT-12 Machined Aluminum Parts

Don't want to see this ad? Sign up for anRPF Premium Membershiptoday. Support the community. Stop the ads.


Corellianexports

Sr Member
RPF PREMIUM MEMBER
image2.jpg


Jawa with Pistol.jpg

gregun.jpg

"Missile" prototype:
IMG_1370.JPG

IMG_1371.JPG

Sight rod with mount:
IMG_1429.JPG

Barrel extension:
IMG_1410.JPG

This is a project of mine that has been a long, long time coming, but as the saying goes, "Better late than never!"

If you're interested in getting some parts for this blaster, please feel free to post a reply with the parts needed.

Parts List:

Side Rod (2x per blaster): $15 each ($30)
Side Rod Point (2x per blaster): $19 each ($38)
Sight Rod w mount: $18 each
Sight Rod mount: $10 each
Rear sight: $17 each (Completed)
Cast Black Resin Pontoon (1x per or 2x?): $6 each ($12)
Barrel Extension: $41
Barrel Extension (for real Ruger): $60+/- (Pending)
Trigger Guard (aluminum): $80 (By Request)
Trigger Guard (resin): $15
COAX Reducers (2x per blaster): $3 each ($6) (In stock)

Standard Kit (Includes all parts above - one Pontoon included - accept the Trigger Guard, COAX reducers and Flash Hider): $150

Full Kit (Includes all the parts above - one Pontoon included - accept COAX reducers and Flash Hider): $165

Deluxe Kit (Includes all the parts above - one Pontoon included - accept Flash Hider): $171

What you will need to complete your blaster:
Tone arm rectangles (2x), Reade Model Kit rods (2x) and Flash Hider/Grill (1x)
These parts can be purchased from vmusicstore on ebay. See below for more information on additional parts.

Update (as of 10/15): I'm happy to announce that all parts have been completed and most all of the kits/parts have shipped.
I have one, spare kit left along with some spare parts.

When sending your payments, please include your rpf ID so I can check you off the waiting list.
If you are sending a payment via "Family/Friends" please remember to include your shipping address within the message section of your
payment or simply send it in a pm. Thanks!

Waiting list:

Side Rods
1. GSmith (4x) (Paid and shipped on 4/20)
2. Crighton (2x) (Payment Pending)
3. Enaswede (2X) (Paid/Shipped 8/7)
4. DarthWilder (2X (Paid 8/17)
5. el toro (2X) (Paid and shipped on 8/13)
6. sjanish (2x) (Shipped 8/14)
7. Obiwan72 (2x) (Paid/Shipped 8/18)
8. scottjua (2x) (Paid/Shipped 7/7)
9. GSmith (4x) (Paid 6/21 - Shipped 6/22)
10. Seneca (2x) (Paid 5/9 - Shipped 5/11)

Side Rod Points
1. GSmith (4x) (Paid and shipped on 4/20/22)
2. Crighton (2x) (Payment Pending?)
3. Enaswede (2X) (Paid/Shipped 8/7)
4. DarthWilder (2X) (Paid 8/17)
5. el toro (2X) (Paid/Shipped)
6. sjanish (2x) (Shipped 8/14)
7. Obiwan72 (2x) (Paid 8/18)
8. scottjua (2x) (Paid/Shipped 7/7)
9. GSmith (4x) (Paid 6/21 - Shipped 6/22)
10. Seneca (2x) (Paid 5/9 and shipped on 5/11)

Sight Rod with Mount
1. Crighton (Payment pending?)
2. Enaswede (Paid/Shipped 8/7)
3. DarthWilder (Paid 8/17)
4. el toro (Paid/Shipped on 8/13)
5. CE (2x) (Completed)
6. sjanish (Shipped 8/14)
7. scottjua (Paid/Shipped 7/7)

Sight Mount Only
1. HB1098S (Paid 6/22 - Shipped 6/27)

Barrell Extension
1. GSmith (2x) (Paid 6/21 - Shipped 6/22)
2. HB1098S (Paid 6/22 - Shipped 6/27)
3. Enaswede (Paid/Shipped 8/7)
4. DarthWilder (Paid 8/17)
5. el toro (Paid/shipped 8/13)
6. sjanish (Shipped 8/14)
7. scottjua (Paid/Shipped 7/7)
8. Seneca (pm sent)
9. Gprops2
10. PropCollector

Rear Sight
1. Crighton (Payment pending?)
2.
3.
4. el toro (Paid/Shipped 8/13)
5. sjanish (Shipped 8/14)
6. scottjua (Paid/Shipped 7/7)
7. TatooineMachine(?)

Trigger Guard
1. Mgoob (Paid 8/7)
2. el toro (Paid/Shipped 8/13)
3. Crighton (Payment pending?)
4. Enaswede (Paid/Shipped 8/7)
5. DarthWilder (Paid 8/17)
6. Mara Jade's Father (Shipped 8/7)
7. Obiwan72 (Paid 8/18)
8. PropCollector
9. Mrwax

Full Kit - Waiting List 1
1. Enaswede (w Trigger Guard) (Paid/Shipped on 8/7)
2. DarthWilder (w Trigger Guard) (Paid 8/17)
3. el toro (w Trigger Guard) (Paid/Shipped 8/13)
4. sjanish (Shipped 8/14)
5. scottjua (Paid/Shipped 7/7)

Full Kit - Waiting List 2
1. Gprops2 (pm sent)
2. PropCollector (Deluxe Kit - Payment pending?)
3. MarcoCazares (Deluxe Kit - Paid 9/6 - shipped 9/8)
4. IMC3 (Deluxe Kit - Paid 9/8 - Shipped 9/10)
5. Mrwax (Deluxe Kit - Paid 9/8 - Shipped 9/10)
6. Hoda (Deluxe Kit - Paid 9/15 - Shipped 9/16)
7.
8.



Additional parts info:
Original Reade Model flash hiders, small "push rods" and machined Rectangular stylus parts for the side rods are available on ebay from vmusicstore (Field Marshall).

Replica Rugers (by KJWorks) like the one pictured below are also available on ebay from unlimitedwares, although listed as "KJW Airsoft MK1 Luger".
IMG_1171.JPG

IMG_1172.JPG

Barrel Extension Install:

IMG_1602.JPG

Use a ruler to mark the brass rod a little over 2" from the end (about 2 1/16"). Use a hacksaw to cut off the 2".

IMG_1603.JPG
Use a belt sander to round off the edges of the brass tube. A file and/or sandpaper can also be used. Test fit the barrel extension. Be sure to turn the part so that the notch is near the top of the barrel:
IMG_1604.JPG
Once fitted in place, use a small tool to tighten the set screw near the bottom edge of the barrel extension.
 
Last edited:

Don't want to see this ad? Sign up for anRPF Premium Membershiptoday. Support the community. Stop the ads.

enaswede

Well-Known Member
RPF PREMIUM MEMBER
I am interested :) This is what I have so far. (see photo below) If you are offering some aluminum parts to replace some of my 3d printed parts that would be awesome! Thanks

IMG_20190216_152105_336~2.jpg
 

Don't want to see this ad? Sign up for anRPF Premium Membershiptoday. Support the community. Stop the ads.

mgoob

Sr Member
RPF PREMIUM MEMBER
I want something solid I can pin into the frame of the pistol as I've got a real Ruger as well as an airsoft.

If we're making things out of metal...
 

Corellianexports

Sr Member
RPF PREMIUM MEMBER
Just finished a prototype side "rod". The length looks good and the two holes appear to be threaded in the reference photos:
IMG_1338.JPG


Thoughts? Comments?

As for a price, depending on the total, some where in the $15 to $20 range per part. I'll know better once I make a second part. There are two rods per blaster.
 

Don't want to see this ad? Sign up for anRPF Premium Membershiptoday. Support the community. Stop the ads.

Don't want to see this ad? Sign up for anRPF Premium Membershiptoday. Support the community. Stop the ads.

Garrett Smith

Active Member
Did you get your dimensions from the actual vintage parts?


Ill take
2 Side Rod (2x per blaster): $19 each
2 Side Rod Point (2x per blaster): $15 each
1 Barrel Extension: Depending on price

When you're ready to sell
 

Corellianexports

Sr Member
RPF PREMIUM MEMBER
I have an actual rear sight that I will be using for dimensions. For the rest of the parts, I'm using reference photos, a Ruger replica and the rear site as a scale for dimensions.
If any one has access to the actual stylus parts, please feel free to post some dimensions or send me a pm. I am making a small adjustment to my rod point blueprint.
 

Don't want to see this ad? Sign up for anRPF Premium Membershiptoday. Support the community. Stop the ads.

Your message may be considered spam for the following reasons:

  1. Your new thread title is very short, and likely is unhelpful.
  2. Your reply is very short and likely does not add anything to the thread.
  3. Your reply is very long and likely does not add anything to the thread.
  4. It is very likely that it does not need any further discussion and thus bumping it serves no purpose.
  5. Your message is mostly quotes or spoilers.
  6. Your reply has occurred very quickly after a previous reply and likely does not add anything to the thread.
  7. This thread is locked.

Don't want to see this ad? Sign up for anRPF Premium Membershiptoday. Support the community. Stop the ads.

Top