Gold Leader 2017 kit alert (and instructions)

[maxhebus]

OH MY........ :love

 

[Yorkie Fett]

Planning on picking one of these kits up, when the funds allow.

Just as a matter of interest, what diameter of tubing would be the best for this kit?

 

[moffeaton]

all the tubes.

Working on it

 

[mrstubbs]

OK. I know the tutorial is coming our but I am down to a few large parts that I can't find a home for. Any feedback would be awesome.

Sent from my SAMSUNG-SM-N910A using Tapatalk

 

[kokkari]

Sidewalls for your left and right pieces, but really the right piece is everywhere on TK. Top piece goes on the engine cans and bottom/middle goes on the inside of the 8rad neck piece on the port/left side I believe

 

[moffeaton]

Yeah some of that gets cut up. Going as fast as I can....

https://www.facebook.com/roboterkampf/posts/10155079603218156?pnref=story

 

[Homecine]

PM sent

 

[moffeaton]

As said above, the middle bottom piece goes on the side of the neck - you have to sand it a bit to fit.

 

[moffeaton]

LOL - that center engine plant on... for the life of me I cannot figure out where it goes. Any ideas?

https://uploads.tapatalk-cdn.com/20170224/7bd288602d20a1491cca66d8c46ffb98.jpgOK. I know the tutorial is coming our but I am down to a few large parts that I can't find a home for. Any feedback would be awesome.

Sent from my SAMSUNG-SM-N910A using Tapatalk

 

[kokkari]

LOL - that center engine plant on... for the life of me I cannot figure out where it goes. Any ideas?

Just so I'm clear, you're talking about this piece?

 

[moffeaton]

Yeah - we cracked it - runs over the seam on the left engine can next to the mount cover!

 

[moffeaton]

Not a lot of good shots of the left engine...

 

[kokkari]

Yeah - we cracked it - runs over the seam on the left engine can next to the mount cover!

View attachment 710368

Did you get all these other locations?

 

[moffeaton]

Yeah those are all molded in - the one that's left off had to be, since it spanned the seam lines on the engine halves, so it wasn't cast-able in-situ.

Did you get all these other locations?
View attachment 710370View attachment 710369View attachment 710372View attachment 710371

 

[moffeaton]

Guys - I am NOT SELLING THIS. If you read the thread, you will find out who is selling this. YOU NEVER BELIEVE WHAT HAPPENS NEXT!

Please stop PMing me about shipping a kit I am not selling, lol.

TEN TIPS FOR SLIMMER ABS!!

Seriously - I'm just building one.

SEE WHAT THESE CELEBRITIES LOOKED LIKE WHEN THEY WERE YOUNGER!

 

[moffeaton]

Just finished the piping and am over the hump - pretty much ready to collate the pics and make the document in a couple days!

 

[Vacformedhero]

As said above, the middle bottom piece goes on the side of the neck - you have to sand it a bit to fit.

View attachment 709885

can you tell me the original parts used on the inside of the 8rad chassis piece, I don't remember seeing them mentioned before ?

 

[moffeaton]

Never IDed so it was 3D sculpted/printed

 

[mslz22]

Just a quick note, I got behind on responding to PM's last week, lots of time doing the accounting for taxes in addition to non stop casting. I think i got back to everyone but if i missed anyone please send a follow up PM.
sorry
mike

 

[maxhebus]

Hi Mike.
I did sent you a pm about original ILM style pilots if you have some time to spare.
And thank for reminding me about my taxes. Now I need to do them....

Just a quick note, I got behind on responding to PM's last week, lots of time doing the accounting for taxes in addition to non stop casting. I think i got back to everyone but if i missed anyone please send a follow up PM.
sorry
mike