Immortan Joe costume from Mad Max, Fury Road
- Thread starter ahoudini
- Start date
TrapperBlu
Active Member
I think they are 2 big. At least the opening. The real ones arnt majorly tapered
Sent from my SM-G900T using Tapatalk
Sent from my SM-G900T using Tapatalk
Bigboss1o1
Active Member
The opening is about 2in might be a little hard to find a fixture for it but it's workable
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Yea it could be a grill part from an old car or a hood ornament.
Those look pretty good! If I can't make these lawnmower filters work or I accidentally trash them- that's a good option. I think I saw some filters like that at Wallyworld but they were slightly more expensive and orange! LOL!
Bigboss1o1
Active Member
Made my own holster looks ok to me yay
Sent from my iPhone using Tapatalk
TrapperBlu
Active Member
Nice take that orange tip off dog or paint it ha ha
Sent from my SM-G900T using Tapatalk
Sent from my SM-G900T using Tapatalk
A smaller vacuum?
Hamsterstyle
Well-Known Member
Whats the diameter of this? I want to figure out if mine is even close to the right size.
Bigboss1o1
Active Member
Oh lol my bad
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
The belt sprocket I have is 9 - 3/16" - also weighs about 2.5 lbs :lol
EDIT: I've since realized this sprocket is close but clearly not a match!
Last edited:
Bigboss1o1
Active Member
Actually mine isn't that big. It's 7 7/8" or 200mm
Oh about that cross bar holding the skull I think it's either a part of a grill or could be a side trim from an older car.
Sighh I went from having this weight off my shoulders and relaxing a bit to having it come right back and have a comfy seat.
Searching for the 100% part is proving frustrating, as I'm sure you found predator! I can scale pretty darn close based on known measurements, and the screen sprocket is about 8 inches, maybe just a bit over. it has 44 teeth, 6 narrow slots, straight through (non-tapered) mounting holes drilled very close to the inside opening (less than half a hole diameter), and a raised lip for the gear teeth. The screen slots are perfectly radial with circular ends, as though milled on a rotating platen with no bit movement. The 'narrow slots' is whats proving hard to find with all the other criteria, tons of sprockets with fat slots. yamaha and kawasaki are coming up closest so far.
Just saying, in case anybody feels like scratching that 'i love finding exact matches' itch lol.
After scrolling through 9000 listings for "44T rear sprocket" the closest I got was this crappy stock photo featuring a gear very close in proportions at least http://www.ebay.com/itm/331472419259?_trksid=p2060353.m1438.l2648&ssPageName=STRK:MEBIDX:IT Of course, the seller cant tell me the part no. of that gear.
Searching for the 100% part is proving frustrating, as I'm sure you found predator! I can scale pretty darn close based on known measurements, and the screen sprocket is about 8 inches, maybe just a bit over. it has 44 teeth, 6 narrow slots, straight through (non-tapered) mounting holes drilled very close to the inside opening (less than half a hole diameter), and a raised lip for the gear teeth. The screen slots are perfectly radial with circular ends, as though milled on a rotating platen with no bit movement. The 'narrow slots' is whats proving hard to find with all the other criteria, tons of sprockets with fat slots. yamaha and kawasaki are coming up closest so far.
Just saying, in case anybody feels like scratching that 'i love finding exact matches' itch lol.
After scrolling through 9000 listings for "44T rear sprocket" the closest I got was this crappy stock photo featuring a gear very close in proportions at least http://www.ebay.com/itm/331472419259?_trksid=p2060353.m1438.l2648&ssPageName=STRK:MEBIDX:IT Of course, the seller cant tell me the part no. of that gear.
Last edited:
Anyone had any luck finding the right or close cam covers for the cross bars on the ceremonial belt? I can't even figure out what to look for to start looking.
