-
Welcome to the Project Runs Forum!
This forum is intended for interest gauging and active runs. Due to the transient nature of this forum, please keep all research and ongoing discussion in one of our main forums so your information is not lost.
Only Premium Members can start a new run.
Unlimited Run Hellboy Tooth Fairy (Dead or Alive)
- Thread starter rgriesbeck
- Start date
Monkey67
Sr Member
Re: Hellboy Tooth Fairy (3D Printed Kit)
looking at the movie fairy the wings seem to be torn. I dont know if it just one or all of them. plus look at the two front teeth seem to be longer. Well i just looked at a few and they seem to come in both ways. So its no biggie
I'm still interested for sure. You think they will be ready by Oct?
looking at the movie fairy the wings seem to be torn. I dont know if it just one or all of them. plus look at the two front teeth seem to be longer. Well i just looked at a few and they seem to come in both ways. So its no biggie
I'm still interested for sure. You think they will be ready by Oct?
Re: Hellboy Tooth Fairy (3D Printed Kit)
Agree with the wings, we're not done yet, needs fune tuning. I'd say done by September, hopefully. It's a side project, not going to sell many, won't make much money on each one, but I do want one on my desk
Agree with the wings, we're not done yet, needs fune tuning. I'd say done by September, hopefully. It's a side project, not going to sell many, won't make much money on each one, but I do want one on my desk
aussiedave
New Member
Re: Hellboy Tooth Fairy (3D Printed Kit)
Watching with interest. They certainly looked cool in the movie. I assume you are aiming at "movie accurate" when completed?
David
Watching with interest. They certainly looked cool in the movie. I assume you are aiming at "movie accurate" when completed?
David
Re: Hellboy Tooth Fairy (3D Printed Kit)
Yes, also there is a Gentle Giant version ($899) on eBay, it'll be a lot like that
Yes, also there is a Gentle Giant version ($899) on eBay, it'll be a lot like that
aussiedave
New Member
Re: Hellboy Tooth Fairy (3D Printed Kit)
Sounds good. I love movie accurate. I guess that is what this entire site is devoted to.
Hopefully you you will come in under $899.......
Hope you find some more time between your other projects!
Sounds good. I love movie accurate. I guess that is what this entire site is devoted to.
Hopefully you you will come in under $899.......
Hope you find some more time between your other projects!
picosbeak123
Active Member
Re: Hellboy Tooth Fairy (3D Printed Kit)
Can't wait to see it finished! Keep going guys!
Can't wait to see it finished! Keep going guys!
Re: Hellboy Tooth Fairy (3D Printed Kit)
Got a bit of time, gunna play with this again. May end up 3d printing it, or may mold it, stay tuned
Got a bit of time, gunna play with this again. May end up 3d printing it, or may mold it, stay tuned
Dragontomb
Well-Known Member
Re: Hellboy Tooth Fairy (3D Printed Kit)
Interested depending upon the price.
Interested depending upon the price.
Re: Hellboy Tooth Fairy (3D Printed Kit)
Weekend bump
Weekend bump
Re: Hellboy Tooth Fairy (3D Printed Kit)
Thanks, we're currently figuring out the best way to break this little guy up, I'm not sure about the dead and displayed option, but I like it. Will see what we can do. It would require a different head, probably different arms too...
Thanks, we're currently figuring out the best way to break this little guy up, I'm not sure about the dead and displayed option, but I like it. Will see what we can do. It would require a different head, probably different arms too...
Last edited:
Re: Hellboy Tooth Fairy (3D Printed Kit)
Stay tuned, spending some hours on this tomorrow
Stay tuned, spending some hours on this tomorrow
Re: Hellboy Tooth Fairy (3D Printed Kit)
Spent 5 hours today on the TF, didn't quite finish, but definitely close. It's mostly cut up, ball joints created that should allow a good amount of posability. The plan is to have a live TF, holding a tooth. Then have an add-on kit, that would let people do the dead and displayed version. It would have an alternate head and arms... Will have some final images soon, then will be accepting deposits
Spent 5 hours today on the TF, didn't quite finish, but definitely close. It's mostly cut up, ball joints created that should allow a good amount of posability. The plan is to have a live TF, holding a tooth. Then have an add-on kit, that would let people do the dead and displayed version. It would have an alternate head and arms... Will have some final images soon, then will be accepting deposits
Re: Hellboy Tooth Fairy (3D Printed Kit)
A small update:
A small update:
Similar threads
