-
Welcome to the Project Runs Forum!
This forum is intended for interest gauging and active runs. Due to the transient nature of this forum, please keep all research and ongoing discussion in one of our main forums so your information is not lost.
Only Premium Members can start a new run.
Unlimited Run Hellboy Samaritan (3D Printed Kit)
- Thread starter rgriesbeck
- Start date
Re: Fully 3D Printed Hellboy Samaritan Kit
I use apoxie sculpt, but any putty that will stick to plastic. The more you sand, the better it'll look. I start at 80, then 150, then 220.
Re: Fully 3D Printed Hellboy Samaritan Kit
Ring kit on its way tomorrow
- - - Updated - - -
Ring kit on its way tomorrow
Ring kit on its way tomorrow
- - - Updated - - -
Ring kit on its way tomorrow
Re: Fully 3D Printed Hellboy Samaritan Kit
Thank you all for the great feedback
Thank you all for the great feedback
Re: Fully 3D Printed Hellboy Samaritan Kit
Got my kit today! As all others have said-WOW. Super excited to start on this.
This is my first resin kit, so I do have a couple of questions that I didn't see addressed-
Should all the half pieces be 'flat' sanded before assembly? I have had to do this before, with just taping a piece of sandpaper to the table, & then moving the piece in a circular motion til flush? Or, just glue all halves together & then puttying & sanding for the smooth edges?
If there's just supposed to be a combination of both techniques, then good enough. I just didn't want to say, sand the 2 halves & then not have the room for the trigger or hammer.to move.
Thanks again for the kit.
:thumbsup
Got my kit today! As all others have said-WOW. Super excited to start on this.
This is my first resin kit, so I do have a couple of questions that I didn't see addressed-
Should all the half pieces be 'flat' sanded before assembly? I have had to do this before, with just taping a piece of sandpaper to the table, & then moving the piece in a circular motion til flush? Or, just glue all halves together & then puttying & sanding for the smooth edges?
If there's just supposed to be a combination of both techniques, then good enough. I just didn't want to say, sand the 2 halves & then not have the room for the trigger or hammer.to move.
Thanks again for the kit.
:thumbsup
Re: Fully 3D Printed Hellboy Samaritan Kit
Glad you like it.
Doesn't really matter, a bit of sanding can't hurt, but you don't need to do much. You'll need to fill the seams no matter. Good luck , lemme know if you have any more questions
Got my kit today! As all others have said-WOW. Super excited to start on this.
This is my first resin kit, so I do have a couple of questions that I didn't see addressed-
Should all the half pieces be 'flat' sanded before assembly? I have had to do this before, with just taping a piece of sandpaper to the table, & then moving the piece in a circular motion til flush? Or, just glue all halves together & then puttying & sanding for the smooth edges?
If there's just supposed to be a combination of both techniques, then good enough. I just didn't want to say, sand the 2 halves & then not have the room for the trigger or hammer.to move.
Thanks again for the kit.
Glad you like it.
Doesn't really matter, a bit of sanding can't hurt, but you don't need to do much. You'll need to fill the seams no matter. Good luck , lemme know if you have any more questions
Re: Fully 3D Printed Hellboy Samaritan Kit
Just realized that I said "resin" kit . I meant 3D printed kit.My bad:facepalm
Thanks for the info. tue got to grab Some Sandpaper tonight get started tomorrow.
Just realized that I said "resin" kit . I meant 3D printed kit.My bad:facepalm
Thanks for the info. tue got to grab Some Sandpaper tonight get started tomorrow.
Nopal
Well-Known Member
Re: Fully 3D Printed Hellboy Samaritan Kit
i also used Apoxie Putty. Worked great for this project.
i also used Apoxie Putty. Worked great for this project.
Re: Fully 3D Printed Hellboy Samaritan Kit
Check this out:
http://www.therpf.com/f13/3d-printed-hellboy-sidearm-comic-version-209414/#post3250502
Check this out:
http://www.therpf.com/f13/3d-printed-hellboy-sidearm-comic-version-209414/#post3250502
Re: Fully 3D Printed Hellboy Samaritan Kit
Sending out a kit to tk2647 today
Sending out a kit to tk2647 today
Re: Fully 3D Printed Hellboy Samaritan Kit
Remember, share your pics!
Remember, share your pics!
Nopal
Well-Known Member
task283
New Member
Re: Fully 3D Printed Hellboy Samaritan Kit
Hi there. Just to let you know I called paypal this morning and the funds should be available for me to send tomorrow. Apologies again. I chose the slowest transfer method known to man apparently.
Rgds
Colin P
Sent from my GT-I9505 using Tapatalk
Hi there. Just to let you know I called paypal this morning and the funds should be available for me to send tomorrow. Apologies again. I chose the slowest transfer method known to man apparently.
Rgds
Colin P
Sent from my GT-I9505 using Tapatalk
Re: Fully 3D Printed Hellboy Samaritan Kit
No problem,
It's sitting in my car all ready to go
No problem,
It's sitting in my car all ready to go
task283
New Member
Re: Fully 3D Printed Hellboy Samaritan Kit
PAYMENT SENT! Yeesh I need to use paypal more often. Apologies once again for the delay.
No problem,
It's sitting in my car all ready to go
PAYMENT SENT! Yeesh I need to use paypal more often. Apologies once again for the delay.
Similar threads
