hez1
New Member
It's probably a little too early for feedback on this, but it's just about at a stage where it doesn't look like a lumpy mess, and I'm finally starting to feel like it's going somewhere and that people will be able to tell what it is . I thought I'd show it off, get the anticipation flowing.
Hopefully this will be finished soon, but you know how it is with sculpts.
______________________________________
Update: 13/5.
Done a lot of work on the mouth area. It took several tries to get right, I think I filled it back in twice, after doing all those cut outs...that's a heart wrenching moment right there, when you realise it's just not right and needs to be completely redone. I won't lie, I wondered briefly if anyone would notice that the curve wasn't right. Then I remembered that I had to put it on my wall too, and that just wasn't gonna fly.
Big thanks to INKMONSTER who emailed me with a tip on the hoses used on the original sculpt, and damn if he wasn't bang on the money. I was not looking forward to sculpting in all those little grooves. Done some smoothing, but there's still a lot more to do. Still, I think the overall shape is now about where I want it, we're really getting into details. Go Gort!
_______________________________________
Update 16/5
Added the four raised ridges on either side of the dome. It's difficult to work out from pics whether they're supposed to be symmetrical or not. One pic I have shows them distinctly asymmetrical, but in others, they would seem to be more or less symmetrical. I've kind of plumped for half and half, they're very slightly asymmetrical, but much more even than a couple of pics would indicate. Also done some work on the mouth area, refining some details, and smoothing the dome.
Let me have opinions, if anyone thinks I've missed something or have done something wrong, now is the time to tell me!
_______________________________________
Update 27/5
OK, I've made a few changes...the dome has been flared out wider near the top, and the ridges have been thickened up a little. The cheeks have been trimmed down a little and the mouth has been tidied up. The pics are pretty dark in the mouth area, so I'm not sure if more changes are needed...I'll keep staring until I work it out. The side details have been roughed in under the dome as well, although only on that one side. Getting close now...
_______________________________________
Update 31/5
Alright, almost finished...there's still some smoothing to do, and a little bit more detail work, but this is basically it. If anyone sees anything that's terribly wrong, keep it to yourself please or you might make me cry. Also, the very back of the bio still needs some work...don't worry, I know it doesn't look right.
OK, pictures...and I was just kidding, I do want feedback, I want this to be the best possible. In the very last pic, there ARE two washers on the dome, but I used nylon ones, so you might have to look closely to make them out. I need to go to the hardware store and buy some more.
Hopefully this will be finished soon, but you know how it is with sculpts.
______________________________________
Update: 13/5.
Done a lot of work on the mouth area. It took several tries to get right, I think I filled it back in twice, after doing all those cut outs...that's a heart wrenching moment right there, when you realise it's just not right and needs to be completely redone. I won't lie, I wondered briefly if anyone would notice that the curve wasn't right. Then I remembered that I had to put it on my wall too, and that just wasn't gonna fly.
Big thanks to INKMONSTER who emailed me with a tip on the hoses used on the original sculpt, and damn if he wasn't bang on the money. I was not looking forward to sculpting in all those little grooves. Done some smoothing, but there's still a lot more to do. Still, I think the overall shape is now about where I want it, we're really getting into details. Go Gort!
_______________________________________
Update 16/5
Added the four raised ridges on either side of the dome. It's difficult to work out from pics whether they're supposed to be symmetrical or not. One pic I have shows them distinctly asymmetrical, but in others, they would seem to be more or less symmetrical. I've kind of plumped for half and half, they're very slightly asymmetrical, but much more even than a couple of pics would indicate. Also done some work on the mouth area, refining some details, and smoothing the dome.
Let me have opinions, if anyone thinks I've missed something or have done something wrong, now is the time to tell me!
_______________________________________
Update 27/5
OK, I've made a few changes...the dome has been flared out wider near the top, and the ridges have been thickened up a little. The cheeks have been trimmed down a little and the mouth has been tidied up. The pics are pretty dark in the mouth area, so I'm not sure if more changes are needed...I'll keep staring until I work it out. The side details have been roughed in under the dome as well, although only on that one side. Getting close now...
_______________________________________
Update 31/5
Alright, almost finished...there's still some smoothing to do, and a little bit more detail work, but this is basically it. If anyone sees anything that's terribly wrong, keep it to yourself please or you might make me cry. Also, the very back of the bio still needs some work...don't worry, I know it doesn't look right.
OK, pictures...and I was just kidding, I do want feedback, I want this to be the best possible. In the very last pic, there ARE two washers on the dome, but I used nylon ones, so you might have to look closely to make them out. I need to go to the hardware store and buy some more.