Cyborg Ninja (Metal Gear Solid) - pics of completed costume
- Thread starter pandamajik
- Start date
Re: Cyborg Ninja (Metal Gear Solid)
That's true, if you want the file for Raiden's Helmet I have it.
EDIT: Ah hell here's the file.
MGS Raiden Helmet.pdo
That's true, if you want the file for Raiden's Helmet I have it.
EDIT: Ah hell here's the file.
MGS Raiden Helmet.pdo
Last edited:
Solochaser
Well-Known Member
Re: Cyborg Ninja (Metal Gear Solid)
I like the build but the eyes look a little to big. They are more thin in the game.
I like the build but the eyes look a little to big. They are more thin in the game.
pandamajik
Member
Re: Cyborg Ninja (Metal Gear Solid)
Only Gray Fox. I've only played the first MGS, maybe someday I'll actually get around to playing the rest.
Thanks but for now I don't have plans for Raiden. Maybe someone else will be able to put it to good use.
Hmm, I can kind of see that now too but I designed all the lines based on the art from the art book since it shows all the different views. I specifically measured the eye height based on relationship to the central eye so maybe the central eye is a tad large as well? But then again, in some of the art the width of the eye slots are just so far apart that it wouldn't have been possible for him to see out of. Another thing is that a lot of the times you see him in game his head is tilted down so that might make the eyes look even more narrow.
Either way I don't think I'm really planning on changing the eye height at this point. Besides, with the current height I can see out of it pretty well whereas if it was thinner it would start obscuring vision. The last thing I want is for someone to have to lead me around when I'm wearing this because I can't actually see out of it.
Only Gray Fox. I've only played the first MGS, maybe someday I'll actually get around to playing the rest.
Thanks but for now I don't have plans for Raiden. Maybe someone else will be able to put it to good use.
Hmm, I can kind of see that now too but I designed all the lines based on the art from the art book since it shows all the different views. I specifically measured the eye height based on relationship to the central eye so maybe the central eye is a tad large as well? But then again, in some of the art the width of the eye slots are just so far apart that it wouldn't have been possible for him to see out of. Another thing is that a lot of the times you see him in game his head is tilted down so that might make the eyes look even more narrow.
Either way I don't think I'm really planning on changing the eye height at this point. Besides, with the current height I can see out of it pretty well whereas if it was thinner it would start obscuring vision. The last thing I want is for someone to have to lead me around when I'm wearing this because I can't actually see out of it.
pandamajik
Member
Re: Cyborg Ninja (Metal Gear Solid)
I've been working the last few days on several rounds of filling, priming, and sanding. It's been sanded up to 600 grit wet sanding so it's very smooth. I have a link to my JY interest thread a few posts up so if you're interested PLEASE reply in that thread. I don't have a set price since it's kind of pending how much interest there is. I'm also not sure how much this kind of piece normally goes for. It's difficult to compare this to something as mainstream as Iron Man or Stormtrooper helmets in terms of both demand and output.
Pictures of the completed master.
I've been working the last few days on several rounds of filling, priming, and sanding. It's been sanded up to 600 grit wet sanding so it's very smooth. I have a link to my JY interest thread a few posts up so if you're interested PLEASE reply in that thread. I don't have a set price since it's kind of pending how much interest there is. I'm also not sure how much this kind of piece normally goes for. It's difficult to compare this to something as mainstream as Iron Man or Stormtrooper helmets in terms of both demand and output.
Pictures of the completed master.
pandamajik
Member
Re: Cyborg Ninja (Metal Gear Solid)
Quick update: For those who have not checked out the interest thread yet, I'm setting the price for casts at 150.
I just placed an order for all the mold making materials, only the best: Rebound 25, Smoothcast 65D and Plasti Paste. That stuff is expensive so I went ahead and ordered the gallon sizes of everything to save a bit on cost.
Just to double check with you guys, I can only use NSP clay when working with Rebound 25 since it's a silicone rubber correct?
Quick update: For those who have not checked out the interest thread yet, I'm setting the price for casts at 150.
I just placed an order for all the mold making materials, only the best: Rebound 25, Smoothcast 65D and Plasti Paste. That stuff is expensive so I went ahead and ordered the gallon sizes of everything to save a bit on cost.
Just to double check with you guys, I can only use NSP clay when working with Rebound 25 since it's a silicone rubber correct?
jackhellcrow
New Member
Re: Cyborg Ninja (Metal Gear Solid)
Please show us how u are going to make it open in the face. \o
Please show us how u are going to make it open in the face. \o
pandamajik
Member
Re: Cyborg Ninja (Metal Gear Solid)
I'll be using neodymium magnets since it's easier than designing a sliding hinge system. I know it's possible but in the interest of time I think magnets will be the faster method.
I'll try to get some pictures up later tonight but so far I've got all the pieces covered in Rebound 25. I'm going to wait a full day for it to fully cure before applying the mother mold. I've got 4 layers of silicone rubber on there (print coat, 2nd coat, 3rd thickened coat, 4th normal coat to smooth final surface). That should be enough right? It's on thick enough that I can't see the color of the primer through the silicone anymore (it was still visible after the 2nd coat).
Also, are there recommendations on sizing and height of registration keys? I made some that are about 3cm thick and I also made some using a paint palette but those round ones are only about 1.5cm thick. The thicker ones started out as round pucks but I cut them down into halves and quarters.
I'll be using neodymium magnets since it's easier than designing a sliding hinge system. I know it's possible but in the interest of time I think magnets will be the faster method.
I'll try to get some pictures up later tonight but so far I've got all the pieces covered in Rebound 25. I'm going to wait a full day for it to fully cure before applying the mother mold. I've got 4 layers of silicone rubber on there (print coat, 2nd coat, 3rd thickened coat, 4th normal coat to smooth final surface). That should be enough right? It's on thick enough that I can't see the color of the primer through the silicone anymore (it was still visible after the 2nd coat).
Also, are there recommendations on sizing and height of registration keys? I made some that are about 3cm thick and I also made some using a paint palette but those round ones are only about 1.5cm thick. The thicker ones started out as round pucks but I cut them down into halves and quarters.
pandamajik
Member
Re: Cyborg Ninja (Metal Gear Solid)
Been hard at work the last few days making the mold. The materials came in last Thursday and I went straight to work.
Here's a picture of the first pull. I had a few issues here and there but the main reason is that it was my first time using these materials and methods.
The INT thread in the JY has been changed to a FS one.
Been hard at work the last few days making the mold. The materials came in last Thursday and I went straight to work.
Here's a picture of the first pull. I had a few issues here and there but the main reason is that it was my first time using these materials and methods.
The INT thread in the JY has been changed to a FS one.
pandamajik
Member
Re: Cyborg Ninja (Metal Gear Solid)
I'll sell it if someone wants it. I'm not even sure how much to charge for it. It's "usable" as in all the pieces are the right shape and the edges are correct in that they should fit. There's some areas that are a bit thinner and some areas in the back piece that got shifted because I took one side of the mother mold off too early (I ended up adding another layer or two of resin) so it shifted some. Basically, it'll take some work. I'm actually fairly happy with how it's turned out for my first foray into molding and casting.
I'll sell it if someone wants it. I'm not even sure how much to charge for it. It's "usable" as in all the pieces are the right shape and the edges are correct in that they should fit. There's some areas that are a bit thinner and some areas in the back piece that got shifted because I took one side of the mother mold off too early (I ended up adding another layer or two of resin) so it shifted some. Basically, it'll take some work. I'm actually fairly happy with how it's turned out for my first foray into molding and casting.
Re: Cyborg Ninja (Metal Gear Solid) - first raw cast
Looking good!
Now make with the Paint and lights!!!!!
Nick
Looking good!
Now make with the Paint and lights!!!!!
Nick
pandamajik
Member
Re: Cyborg Ninja (Metal Gear Solid) - first raw cast
I'm actually starting to work on the rest of the suit too. I should get some pics of the sword too since it's all painted.
Looking good!
Now make with the Paint and lights!!!!!
Nick
I'm actually starting to work on the rest of the suit too. I should get some pics of the sword too since it's all painted.
Judge Spartan
Sr Member
Re: Cyborg Ninja (Metal Gear Solid) - first raw cast
What! You're working on the other parts and no progress pics on those! J.K. Progress pics when you can. Can't wait to see them...
What! You're working on the other parts and no progress pics on those! J.K. Progress pics when you can. Can't wait to see them...
pandamajik
Member
Re: Cyborg Ninja (Metal Gear Solid) - first raw cast
Here are some pictures of where the sword is at right now (pretty much only need to wrap the handle). It's made from poplar and sintra. The tsuba and habaki are separate pieces and can actually be removed. I could have glued it all together but I thought it was a neat touch.
On a somewhat related note, if you still want a cast please let me know in my JY thread or via PM. I still need confirmation even if you initially expressed interest when it was still an INT thread.
Here are some pictures of where the sword is at right now (pretty much only need to wrap the handle). It's made from poplar and sintra. The tsuba and habaki are separate pieces and can actually be removed. I could have glued it all together but I thought it was a neat touch.
On a somewhat related note, if you still want a cast please let me know in my JY thread or via PM. I still need confirmation even if you initially expressed interest when it was still an INT thread.
