Poikilotherm
Sr Member
deleted
Last edited:
-
Welcome to the Project Runs Forum!
This forum is intended for interest gauging and active runs. Due to the transient nature of this forum, please keep all research and ongoing discussion in one of our main forums so your information is not lost.
Only Premium Members can start a new run.
Done / Completed **LINEAGE** Foundry Cast ANH Kenobi Stunt Hilts (ANH/ROTJ - V2/V3)
- Thread starter PoopaPapaPalps
- Start date
Got my V3! Thanks PPP!
Best ”Aluminium Candle Stick Holder” ever! Haha
Plan on going for a pre Don Bies stunt build. Got everything I need.
Now the fun begins!
Best ”Aluminium Candle Stick Holder” ever! Haha
Plan on going for a pre Don Bies stunt build. Got everything I need.
Now the fun begins!
PoopaPapaPalps Would it be possible to switch my blank on the 4th run to a V3 stunt? Then could also put me down for another V2 and a Blank in the last run?
Welcome to the club!
Done and done. I've got some machining to do this week so, with any luck, I'll have these out to mail pretty soon and working on the next run after.
Bump for more interest for future runs.
Thank you sir!
To anyone on the fence about these, you should absolutely sign up. These hilts are seriously awesome!
Finished putting together my V3. Absolutely love this hilt. I held off getting a V3 for years as I always wanted a cast one.
I did this one up as best as I could to resemble the stunt used in the throne room scene. I took a few liberties. Basically just painted it like the stunt in the warehouse scene and added a clamp and card.
I had an old Buggy Whip that I cut down and used as a blade. It works as a good substitute to using a vintage antenna though I suspect it’s diameter is not as thick as it should be.
The clamp card I used was from a board out of an old decommissioned telecom cabinet.
Thanks again PoopaPapaPalps!
I did this one up as best as I could to resemble the stunt used in the throne room scene. I took a few liberties. Basically just painted it like the stunt in the warehouse scene and added a clamp and card.
I had an old Buggy Whip that I cut down and used as a blade. It works as a good substitute to using a vintage antenna though I suspect it’s diameter is not as thick as it should be.
The clamp card I used was from a board out of an old decommissioned telecom cabinet.
Thanks again PoopaPapaPalps!
List updated and bump for further interest!
I had to take a few days to visit some family but the 4th run is close to being done. One of the casts proved a bit more difficult to machine. I don't fully understand the properties of alu casting yet, but there might be some hardening in some over others. Some just take to machining easier, while others are a bit more robust. Nothing major but just slower in getting the work done.
I had to take a few days to visit some family but the 4th run is close to being done. One of the casts proved a bit more difficult to machine. I don't fully understand the properties of alu casting yet, but there might be some hardening in some over others. Some just take to machining easier, while others are a bit more robust. Nothing major but just slower in getting the work done.
...Aaaand Run 4 is out the door! I've already sent out messages to those on that run, and I'll be gearing up to do the 5th run pretty soon here.
Poikilotherm
Sr Member
deleted
Last edited:
That looks great Poikilotherm! What color/type of paint did you use? It looks way closer than I've been able to find?
Poikilotherm
Sr Member
deleted
Last edited:
Got a potential spot in the 5th run opening up if anyone is interested in taking it.
So bump for more interest.
So bump for more interest.
I wouldn't mind if you move my v3 from the 7th run to fill the spot so I get it together with the v2
Oops, I meant to put 6th Run. The 5th run is still a go.
Done and done.
Similar threads
