STAR WARS - Skeleton Crew props & costume

[Rubibilly]

I think the small clips can be found on Amazon, not sure if I'm allowed to post a link. Looks like they got them before they were manufactured into the clips or they just carefully separated and flattened them . Doing so gives you the rounded "wings" with holes on the side.

Great, many thanks

 

[TK41434]

I think the small clips can be found on Amazon, not sure if I'm allowed to post a link. Looks like they got them before they were manufactured into the clips or they just carefully separated and flattened them . Doing so gives you the rounded "wings" with holes on the side.

Which size do the clips have?

 

[Halliwax]

Always amazes me how they come up with this stuff that “just works”

 

[Rubibilly]

Which size do the clips have?
View attachment 1892763

38mm

 

[joberg]

Great, many thanks

Yes, these seems to be of the Bulldog brand (U.K.). You're right, you have to separate them and flatten the "ears" (they are holding the spring inside the clip). You can even use the original spring to make your prop.

 

[BENnotKENOBI]

Unfortunately, they use different springs. The best bet is trying to get a set like this to find the right size.

 

[lonepigeon]

Yep, same little outlined blue square on both sides keeping the gap even but maybe LEDs?

View attachment 1891297

I think those might just be little bits of the sides of the blue button cover.
If they trimmed them, they may have cut a little more off the top which left the sides longer. Figuring the short side there is completely cut off.
I have two different size blues. One is a little smaller than the other.
Instead of the more typical 12.8mm width my smaller one is about 12mm. The length is also about 1mm shorter.

 

[the.rebel.agent]

I think those might just be little bits of the sides of the blue button cover.
If they trimmed them, they may have cut a little more off the top which left the sides longer. Figuring the short side there is completely cut off.
I have two different size blues. One is a little smaller than the other.
Instead of the more typical 12.8mm width my smaller one is about 12mm. The length is also about 1mm shorter.

12mm is from EAO? They have a lot of models

 

[lonepigeon]

12mm is from EAO? They have a lot of models

I thought the 12.8mm is EAO? I doubt they made both so close in size.
I just dug some out of my parts bins. I haven't bought any on purpose, but have some from various electronics parts lots over the years.

 

[Anakin Starkiller]

Absolutely High Republic vibes going on there.

I like it a lot more than anything from Acolyte!

 

[the.rebel.agent]

I thought the 12.8mm is EAO? I doubt they made both so close in size.
I just dug some out of my parts bins. I haven't bought any on purpose, but have some from various electronics parts lots over the years.

I could not find any smaller lens cover on EAO website. They have 1000 models or so, but smaller ones seems to be 12.8mm so far. Will keep looking cause I saw some Chinese push buttons designed for 12mm panel hole. So their lens should be smaller for sure. EAO are 16mm panel hole.

 

[lonepigeon]

Maybe two half lenses stacked vertically?
This one is 15.30mmx21.50mm

 

[thawn_es]

38mm

38mm???
I think are too bigs...
I found a 23mm clips

 

[TK41434]

You can find these isolations crimps in different sizes ...

The question is ... what they used (watch C in the table, in mm)?
This might answer what size they used for the clips too.

 

[Rubibilly]

38mm???
I think are too bigs...
I found a 23mm clips
View attachment 1893340

I think it's to small

 

[thawn_es]

I think it's to small

If the clip is 38mm the patch is 12cm aprox long.
If the clip is 23mm the patch is 7,5cm aprox long.

 

[the.rebel.agent]

KB torch. This was hard, but coolest ID. There are other labels too, like TOPKAY. Same manufacturer, customized label. She is actually using two.

 

[Halliwax]

That’s a dang cool torch

 

[the.rebel.agent]

Fern gloves are SANITIOR 822304 half finger gloves from Amazon

 

[pburgess]

Any motorcycle people that might recognize Captain Brutus’ boots? Perhaps that zigzag/diagonal motif (green arrow) is some brand’s trademark? Scribbled out red parts are costume dept greeblies; ignore. I’ve searched what feels like thirty million boots and still no match. Much appreciated!