Pulse Rifle 3d print Files, SPAS cage/Remington/clam shell shroud, racking etc,,


2keepandbear

Active Member
SO I have run into a little issue - 100% my fault, but In printing the upper receiver, the slot for the bolt handle got screwed up in printing. I printed the receiver with the top laying on the print bed and supports for only what touches the build plate (using cura). Just curious on what your settings are and/or how you print the receiver.
 

Attachments

  • A0107C71-4EE8-46A4-86C3-DCA35591EF89.jpeg
    A0107C71-4EE8-46A4-86C3-DCA35591EF89.jpeg
    2.5 MB · Views: 46

Seananigans

Well-Known Member
New Mk3 shroud nearly ready for resin printing then mould making, it’s going to be cast in tough urethane resin, will come in both Aliens and Alien3 commando versions. Accepts a real spas12 heat shield and a real or Airsoft Thompson and my printed variants.
Recess for a metal plate(s) in the mag well for that metal on metal sound when the magazine is inserted.
4CA15D2B-12CD-49F5-B9D0-427BB0FB5928.jpeg
95EE1CDD-981D-4E60-8D28-A4459F13657A.jpeg
7D232C7B-800C-487B-B145-9508FB166CB4.jpeg
14446C1D-26FF-454F-8C82-0E008D0563E6.jpeg
63F60951-14D8-4884-9830-27873D92DD43.jpeg
BCE753EB-B447-495B-B446-A20D3C4F4252.jpeg
66031366-93FA-4FEC-ADB5-F5F75F1B71DA.jpeg
47AED191-720A-4EE1-83DE-705EA50CFB12.jpeg
3EC96A66-AC98-4A15-9BB9-51558686732D.jpeg
EFB6BF90-641B-4FE8-8CAA-CE688B2EB617.jpeg
 

Flip

New Member
Sorry I have another question. Do you know the size and type of screws used in the build? Also the L bracket do you use only half of it or do you layer them on top of each other?
 

Seananigans

Well-Known Member
Sorry I have another question. Do you know the size and type of screws used in the build? Also the L bracket do you use only half of it or do you layer them on top of each other?
Just buy a multi sized pack of hex button head bolts mate and pick out what fits, same with the springs...I think I used the brand Ronson off Amazon
 

Seananigans

Well-Known Member
SO I have run into a little issue - 100% my fault, but In printing the upper receiver, the slot for the bolt handle got screwed up in printing. I printed the receiver with the top laying on the print bed and supports for only what touches the build plate (using cura). Just curious on what your settings are and/or how you print the receiver.
Support set at 80, pla+ nozzle temperature 235, bed 60, same orientation in your pic with a brim.
 

Flip

New Member
Sorry to bother, but I am having an issue with the MK2 Rem trigger, does it work with the Mk1 Rem assemble? I either have to push it into far so the slide doesn't get stuck under the hammer and then it doesn't snap forward because it is to wide to fit into the back of the rem assemble or to far back and the slide won't work with it? Do you have any pictures so I can see how the trigger is put together with the main body?
 

2keepandbear

Active Member
Hey! Finally getting around to properly printing these files on my Voron... the only issues I have is the Mk2 files I have don't have a two piece SPAS cage and my printer isn't big enough to accommodate the full cage. Any chance you have a two piece design for the spas cage?
 

Your message may be considered spam for the following reasons:

  1. Your new thread title is very short, and likely is unhelpful.
  2. Your reply is very short and likely does not add anything to the thread.
  3. Your reply is very long and likely does not add anything to the thread.
  4. It is very likely that it does not need any further discussion and thus bumping it serves no purpose.
  5. Your message is mostly quotes or spoilers.
  6. Your reply has occurred very quickly after a previous reply and likely does not add anything to the thread.
  7. This thread is locked.
Top