Let’s talk nepenthe

[the.rebel.agent]

Just playing around with the images I cleaned up. Given the reported measurements are "good", this is what I did so far. Guess my bottles didn't clear customs yet, and I had to do something with my free time. ASAP got the bottles, will double check measurements.

 

[the.rebel.agent]

Guess is this very close to the screen used prop. At least for me.

 

[Vaderman]

So, what did you come up with? Do you have the flask measurements?

 

[the.rebel.agent]

So, what did you come up with? Do you have the flask measurements?

Only the ones published. My bottles didn't clear up our customs yet. Got a photo from a box, where they were the same as published, so I do trust a little bit more now than a week ago.

 

[the.rebel.agent]

This is just a print test. Printing orientation is everything when you're talking about FDM printer. This is the best example. Now I will start working on the templates for The Resistor branding and symbols. I also captured a great photo from the tip of the fitting hose.

 

[TJJohn12]

Mine cleared customs an hour ago, but it'll be a few days still because of UPS Mail Innovations

 

[the.rebel.agent]

So far, so good. Any feedback will be welcome...

 

[Mech10]

Not bad, I’m still trying to figure the raised end though. Every decent photo I’ve found suggest them being flat and the paint/weathering of the stripe giving off an illusion. Like said before hopefully one of these gets out in the wild like the imperial cookie/protein bars

 

[the.rebel.agent]

Nobody is watching the show in 4K? There is no doubt about the shape of that thing.

 

[Mech10]

Nobody is watching the show in 4K? There is no doubt about the shape of that thing.

I’ve watched in 4k and have gone frame by frame.
Can you post supporting material for your interpretation? Without telling us to go rewatch the episode again.
This is what I’m seeing

 

[the.rebel.agent]

Don't worry, you don't have to watch the full episode. And there are a few more, But this is very clear

 

[Mech10]

Don't worry, you don't have to watch the full episode. And there are a few more, But this is very clear

I can kind of see it with the second picture but I also see light distortion also. But hey there are no wrong interpretations this early in the game and it’s always good to have healthy discussions

 

[the.rebel.agent]

Totally. Here you have a second batch. I did use a lot of them as canvas on Fusion. But this is only the second iteration. I usually re-create the model more than 3 times until I satisfied.

 

[Halliwax]

I missed a lot here, updates look wicked

 

[the.rebel.agent]

Subtle, but was a mod. Increased the size of the top and bottom symbols, just a little bit. Will create a template to engrave on laser or cut in vinyl. I believe that "the resistor" is only on one side of the bottle, but the symbols are in both...is that right? I just got one photo where It appears that "the resistor" is on both sides too

 

[Halliwax]

Still waiting on my to arrive

 

[the.rebel.agent]

This is what I see from the back. Nepenhé circuit board and connector remains the same, but inverted.

Any feedback will be welcome.

 

[Halliwax]

Still waiting on my damn bottles

 

[OddballFett]

Got mine today. One black and one light grey. It's not silver or metallic looking. Texture is part of the coloured pieces (I'll call them brackets for now) Ignoring the bottle cap the bottle dimensions are roughly: 10.7 x 15.8 x 3.3 cm. The coloured brackets are about 4mm on the thin part. I was hoping they'd slide off quite easily to make swapping them over easy too. But trying to do so manually will result in you losing your nails. Feel free to post solutions!

 

[Halliwax]

Got mine today. One black and one light grey. It's not silver or metallic looking. Texture is part of the coloured pieces (I'll call them brackets for now) Ignoring the bottle cap the bottle dimensions are roughly: 10.7 x 15.8 x 3.3 cm. The coloured brackets are about 4mm on the thin part. I was hoping they'd slide off quite easily to make swapping them over easy too. But trying to do so manually will result in you losing your nails. Feel free to post solutions!

From Amazon?