DarkPassenger
Sr Member
I don't want to get all mushy on everyone but thanks a lot for all the hard work on this Kill Knife research. I don't have the computer skills or brains to figure that out.
Dexter's Kill Bag and Tools
- Thread starter DarkPassenger
- Start date
-
- Tags
- dexter
Those were done with the overall length 13 inches, with 1/8" for the blade and 3/16 for the handles. I used the counter sunk socket head cap screw I linked to earlier for the holes. I don't have the equipment set up just yet, but I should be able to produce these by mid march.
I just noticed I need to remove the fillet's on the back end of the handle. It's not a big deal to change it if we decide it should be 13.25 or whatever, but right now I can fit 2 blades onto a 24" piece of stainless without much waste. I don't think I would be able to do that if I stretched the blade.
franz bolo
Sr Member
I was making mine about 14" but the width on mine was way thinner! That thing looks way to wide.
FB
DarkPassenger
Sr Member
Looks great man! I think where the sharp side meets the handle, it should be flush and the dull side of the blade is rounded off.
franz bolo
Sr Member
Looks good Drew. I still don't think that overhang in the front is like that. Also I think the back of the handle is straight and not curved.
FB
DarkPassenger
Sr Member
That knife actually might not be "the" Kill Knife. That might be the retractable one right before the actual stab. Hard to tell.
Although the average hand width is about 4" so the handle could still be about 6.5"?
franz bolo
Sr Member
The handle slabs look at least 1/4". The blade width looks 3/16". I k now the bottom image is the handle stunt plate version.
FB
FB
itsalive
Well-Known Member
I see. Yeah that is a stunt knife, look at the inner area between the slabs/handles.
The handle is exactly 6.338 inches on the 12.844
Waiting to see how everyone feels about it. Then I'll break it down and upload it.
itsalive
Well-Known Member
3/16 is way to thick though, It's pretty thick for the baseplate knife. I would say that one is 3/16, and most likely so theres enough area across the metal to secure it to the plate with a thick screw. Where is the link to that youtube video. I watched it, but I lost the link. I need to watch that again.
DarkPassenger
Sr Member
itsalive
Well-Known Member
That's the one. Thanks
franz bolo
Sr Member
Yeah, that's probably the retractable knife.
I did a few grabs and got these. I would say maybe 10/16" total thickness??
FB
I did a few grabs and got these. I would say maybe 10/16" total thickness??
FB
I think you're right too. I just threw that together from a version I had started on a while back. If the bottom 2 edges of the handle line up, it would be possible to cut this out of 1.5" stainless, so it would be cheaper. I'll be happy to work something up again, just someone let me know when we come to a consensus on the design.
DarkPassenger
Sr Member
I would say the knife stuck in Jordan is probably accurate. That just the magnetic plated one. No reason to mess with the handle right?
pinder91
Sr Member
Nope. Those have the right look, but are not the correct leather, and do not come in numbered sizes, so they might not fit as well. They are probably the same pattern, however.
I hope you have big hands if you want the real deal, since they've been discontinued for about a year now.
Damascus D301 (smooth back):
I only recall seeing these in all but the last episode of Season 1.
Damascus D301 Ultrathin™ Leather Gloves (No Points)
The now discontinued D301 has been copied by what I'm guessing is the leatherglovesonline house brand.
Tough Gloves Ultra™ Thin Cabretta unlined leather gloves (no points)
Damascus D302 (points on back):
Predominantly seen throughout the rest of the series.
Damascus D302 Ultrathin™ Cabretta unlined leather gloves
And again, the leatherglovesonline version.
Tough Gloves Ultra™ Thin Cabretta unlined leather gloves
Apparently, leatherglovesonline was the original supplier to production as well.
itsalive
Well-Known Member
http://rapidshare.com/files/448353105/killknife.zip
12.844inches
Saved in MM format as a PNG. It should be enough for some waterjet places. The hole should be 2mm wide
If the white fill color gives the waterjet guy trouble. Let me know I can upload the knife and slab png files without the white fill.
12.844inches
Saved in MM format as a PNG. It should be enough for some waterjet places. The hole should be 2mm wide
If the white fill color gives the waterjet guy trouble. Let me know I can upload the knife and slab png files without the white fill.
itsalive
Well-Known Member
http://rapidshare.com/files/448353833/killknifenofill.zip
What the hell- Here's the no fill version.
Image size info in programs like photoshop and illustrator should list
Knife dimensions= 37.888 x 326.221 mm
Slabs dimensions= 37.888 x 160.994 mm
What the hell- Here's the no fill version.
Image size info in programs like photoshop and illustrator should list
Knife dimensions= 37.888 x 326.221 mm
Slabs dimensions= 37.888 x 160.994 mm
Similar threads
