Done / Completed V3 Emitter Limited Run Thread for V2/V3 Builder’s Kit

jorged123 said:
Tracking info has been added for our order. Estimated arrival of emitters is early next week. I have sent PMs requesting shipping/billing information to all run participants. This will help me move along quicker with invoicing and then shipping, once the emitters have been verified.
Click to expand...

25398356-8FD2-40CF-8418-59149D2BA700.jpeg
 
Run status has been updated on Post 1. I have made different colors for order status states. Info Requested, Info Submitted, Invoice Sent, Invoice Paid, and Shipped. I plan on finishing this out as soon as all stages are met. I will do my best to ship these as quickly as possible after I verify that the payments are met. I plan on adding the tracking info to the invoice and PayPal should send tracking info emails as soon as I submit the information. As long as the emitters arrive undamaged, then this should go pretty smoothly since most have already submitted the info I requested.
 
I hope to put up pictures of the finished emitters tonight and start inspecting all emitters before sending invoices. Once all accounted for emitters are good to go and the invoices are paid, then I'll start sending these out via USPS with tracking. Hopefully, my previously quoted international shipping is very close to what I will put on the invoice. I'll ask before sending the invoice if >$5 discrepancy exists from the original quotes.
 
jorged123 said:
I hope to put up pictures of the finished emitters tonight and start inspecting all emitters before sending invoices. Once all accounted for emitters are good to go and the invoices are paid, then I'll start sending these out via USPS with tracking. Hopefully, my previously quoted international shipping is very close to what I will put on the invoice. I'll ask before sending the invoice if >$5 discrepancy exists from the original quotes.
Click to expand...

Fantastic!! I can’t wait to see how these turned out!
 
I am going to go through the process of sending invoices today. I will send them to all who have submitted the info first, obviously. Then once the status has been paid, I will batch send these out with USPS in groups of 10 or so in a first pay first ship basis. I will then do another set of ten or finish it in the second wave. I apologize if this takes longer than desired. I know you are eagerly awaiting these emitters! Hopefully, this will go smoothly. I am new to completing a run and I am learning as I go!

I also plan on sending PMs again to those who haven't responded to my earlier info requests, I know not everybody is on here all the time. Most everybody has already sent the info that I have requested and I thank you all for that boost to this process.
 
No set screws, they aren't on the model or our test prints. We left the 5mm grub screw hole shop to the end user as this may not be in the right place with threading from the shop. Following Halliwax's tutorial for the V3 emitter hole should work. However, the cylinder where the 5mm grub screw goes is a tad bit shorter than the V2 emitter so a new template may be needed for this part-stay tuned. The other holes that are present in the V2 emitter may not actually be on the V3 emitter.
 
You must log in or register to reply here.

Similar threads

Padawan311
Kenobi Series Comlink Aluminum Conversion Parts
2
Replies
37
Views
2,604
Padawan311
Padawan311
bobatrek
Limited Run *** It’s Orderin’ Time! *** FANTASTIC 4: FIRST STEPS - Mission 4 Patch Set ***
2 3 4
Replies
61
Views
6,831
bobatrek
bobatrek
jhusel
Limited Run Star Trek TOS Phaser/communicator Display Stand
Replies
6
Views
974
jhusel
jhusel
DaveP
Interest DaveP's V2 and V3 run - 2024
10 11 12
Replies
238
Views
55,156
gobler
gobler
TheDragon
Limited Run 2nd Run - ROTJ Endor Rebel Helmet 'Halo' Vacuum Formed Shells
2 3 4
Replies
61
Views
6,737
TheDragon
TheDragon
Back
Top