-
Welcome to the Project Runs Forum!
This forum is intended for interest gauging and active runs. Due to the transient nature of this forum, please keep all research and ongoing discussion in one of our main forums so your information is not lost.
Only Premium Members can start a new run.
Done / Completed Star Lord Helmet - All Done
- Thread starter rgriesbeck
- Start date
Re: Star Lord Helmet from 3D Print (collab with TheRocketeer)
Big head = big brain
Big head = big brain
Re: Star Lord Helmet from 3D Print (collab with TheRocketeer)
The raw print is done, just finishing a couple tubes, it will be on it's way to TheRocketeer tomorrow. This pic shows just how much work is required to take a raw 3D print and actually make it into something people would buy.
To those asking for my 3D files, trust me, the amount of work to go from what's above to a smooth, wearable helmet is well worth the $230.00. And no, I won't share :angry
The raw print is done, just finishing a couple tubes, it will be on it's way to TheRocketeer tomorrow. This pic shows just how much work is required to take a raw 3D print and actually make it into something people would buy.
To those asking for my 3D files, trust me, the amount of work to go from what's above to a smooth, wearable helmet is well worth the $230.00. And no, I won't share :angry
maverick07
New Member
Re: Star Lord Helmet from 3D Print (collab with TheRocketeer)
My dome is 22.25 as well so that's a relief and if its a bit big I can always add some foam spacers to the inside and you wouldn't know the difference.
Trust me this is not going to be too large, I have a 22.25" head and I want to be able to wear it too.
My dome is 22.25 as well so that's a relief and if its a bit big I can always add some foam spacers to the inside and you wouldn't know the difference.
maverick07
New Member
Re: Star Lord Helmet from 3D Print (collab with TheRocketeer)
Great job rgriesbeck it looks amazing i'm really excited to see the finished cast you did a fantastic job on these files. count me as definitely in once the run starts.
Great job rgriesbeck it looks amazing i'm really excited to see the finished cast you did a fantastic job on these files. count me as definitely in once the run starts.
Last edited:
cofphoto
Well-Known Member
Re: Star Lord Helmet from 3D Print (collab with TheRocketeer)
I'm pretty new to this, but if it was a little too big, how hard would it be to glue some craft foam inside to make it fit better? Unless you just don't want to see it when it's on display? Seems like it would be pretty difficult to make something like this that fits such a wide variety of people? You could even just slip a piece of craft foam inside and not glue it, I would think?
I'm pretty new to this, but if it was a little too big, how hard would it be to glue some craft foam inside to make it fit better? Unless you just don't want to see it when it's on display? Seems like it would be pretty difficult to make something like this that fits such a wide variety of people? You could even just slip a piece of craft foam inside and not glue it, I would think?
Re: Star Lord Helmet from 3D Print (collab with TheRocketeer)
You can easily shim it with foam to make it fit better. Keep it clean to leave it in while displaying, or use velcro so it's removable
You can easily shim it with foam to make it fit better. Keep it clean to leave it in while displaying, or use velcro so it's removable
Re: Star Lord Helmet from 3D Print (collab with TheRocketeer)
I've got a 23 inch head, which seems pretty average. We're leaving a bit of room for those with 24s, while people with 22s can do as Kevin said, foam it up a bit. The plan is still to use probably a strap to hold the front onto your head, then the back piece will magnet onto the front. Easy peasy
I've got a 23 inch head, which seems pretty average. We're leaving a bit of room for those with 24s, while people with 22s can do as Kevin said, foam it up a bit. The plan is still to use probably a strap to hold the front onto your head, then the back piece will magnet onto the front. Easy peasy
mbmcfarland
Sr Member
Re: Star Lord Helmet from 3D Print (collab with TheRocketeer)
Consider me interested
Consider me interested
vtswordfish
Sr Member
Re: Star Lord Helmet from 3D Print (collab with TheRocketeer)
Add me to the list please!
Add me to the list please!
Re: Star Lord Helmet from 3D Print (collab with TheRocketeer)
I prefer Star ***** Helmet
I prefer Star ***** Helmet
