Halloween costumes air mag conversion

you will have to remove the wires so you will want to replace the lights too. this means opening up the shoe. pulling the liner out form inside to get to the battery and removing the heel cup and "clear" sole.

i used angelus paints and finisher. wore them all day wednesday with no scuffing.
 
Any possible chance you or anyone else could perform this job on my pair? I would pay for it depending on how much it would cost. What would the cost be?
 
Last edited:
cavx said:
When I did mine today, one would not light up, so after changing out inverters etc, I ended up using my tester inverter which outputs a higher then the batteries I am using and it came on. It seems like this stuff needs a good shock every now and then kick it into gear.

What i don't get is why one panel is slightly brighter than the other if they both use the same parts and fresh batteries. Been running them 8 hours solid now, and still bright.
Click to expand...

Ah right, I don't have any other inverters, just the two that came with the kit.

I'll try resoldering this weekend and see how I get on


Sent from my iPhone using Tapatalk
 
Kevzie said:
Ah right, I don't have any other inverters, just the two that came with the kit.

I'll try resoldering this weekend and see how I get on


Sent from my iPhone using Tapatalk
Click to expand...

What voltage you running?

I have 6 of the tiny 3V inverters on hand and no 12V left. I will have to order more 12V inverters soon.

What I noticed with my dodgy panel was if I tapped it, it suddenly came on much brighter, almost as if it is not making a full contact, yet it is soldered.
 
cavx said:
What voltage you running?

I have 6 of the tiny 3V inverters on hand and no 12V left. I will have to order more 12V inverters soon.

What I noticed with my dodgy panel was if I tapped it, it suddenly came on much brighter, almost as if it is not making a full contact, yet it is soldered.
Click to expand...
That is happening to mine.. i need to tape it good.. though i did peel the connector back.. and it is held by some adhesive.. i am going to invest in some crimp connectors.. shipping kills it though lol

Sent from my SM-N920T using Tapatalk
 
bigv69er said:
That is happening to mine.. i need to tape it good.. though i did peel the connector back.. and it is held by some adhesive.. i am going to invest in some crimp connectors.. shipping kills it though lol

Sent from my SM-N920T using Tapatalk
Click to expand...

I honestly can't remember which panel I added more solder to now and which I did not. I only used black electrical tape over the connections where the adhesives stick to themselves, so should be reasonably easy to access. I also only used hot glue to hold the panel to the inside of the strap, so should be able to re-work this without too much trouble.

I have to pull this apart anyway as soon I will be tearing my soles off and adding EL to the soles, then gluing a set of the new clears on. I am also doing EL for the bubble on heel cup, but need to mold cast the new parts first.
 
cavx said:
I honestly can't remember which panel I added more solder to now and which I did not. I only used black electrical tape over the connections where the adhesives stick to themselves, so should be reasonably easy to access. I also only used hot glue to hold the panel to the inside of the strap, so should be able to re-work this without too much trouble.

I have to pull this apart anyway as soon I will be tearing my soles off and adding EL to the soles, then gluing a set of the new clears on. I am also doing EL for the bubble on heel cup, but need to mold cast the new parts first.
Click to expand...
Same here, so it was easy to re-do.. but seems like its not my connection..its the el adhesive that the comnector has

Sent from my SM-N920T using Tapatalk
 
bigv69er said:
Same here, so it was easy to re-do.. but seems like its not my connection..its the el adhesive that the comnector has

Sent from my SM-N920T using Tapatalk
Click to expand...

Mine appears to be soldered onto the sheet. I have other EL sheet here with stick on connectors.
 
cavx said:
Mine appears to be soldered onto the sheet. I have other EL sheet here with stick on connectors.
Click to expand...
Id say crimp connectors are our best bet.. since they go inside the EL itself..and wont budge if compressed correctly..here is a link of what im talking about.. let me know if you want some..since if i buy 20 sets its the same price as buying 10 lol..

https://youtu.be/TXfaPQgdmNA

Sent from my SM-N920T using Tapatalk
 
cavx said:
What voltage you running?

I have 6 of the tiny 3V inverters on hand and no 12V left. I will have to order more 12V inverters soon.

What I noticed with my dodgy panel was if I tapped it, it suddenly came on much brighter, almost as if it is not making a full contact, yet it is soldered.
Click to expand...

It's the 3v inverters that I got with the kit. Gonna try and resolder and maybe switch the inverter to see if it's that and try and narrow Down the problem.


Sent from my iPhone using Tapatalk
 
Since the HC mags aren't waterproof, is it possible to spray a waterproof product on them? Or will the material it's made of not work? If possible, what product would you guys recommend?
 
SunRecords54 said:
Since the HC mags aren't waterproof, is it possible to spray a waterproof product on them? Or will the material it's made of not work? If possible, what product would you guys recommend?
Click to expand...
I wanna try that next... that restolium never wet for shoes

Sent from my SM-N920T using Tapatalk
 
Does anyone know where to get the Loctite Hybrid Glue that Klen was talking about in Canada? Sounds like what a noob such as myself should get but I can't find it anywhere
 
Last edited by a moderator:
Blast818 said:
Does anyone know where to get the Loctite Hybrid Glue that @Klen was talking about in Canada? Sounds like what a noob such as myself should get but I can't find it anywhere
Click to expand...
Do not take the hybrid just go for the professional one that is easier to find and will give you a better result, once your job will be glued it will not move forever ! ;)

1604958-professional-20g.jpg
 
Hey Guys,
I am about to buy some nike air mags from aliexpress for $130 dollars and they look good except it says that the LED lights are not very bright. I was planning on modding them with the toe slim and all that stuff but I was wondering, if I replace the LEDs with the EL sheet, is there a possibility that I will have a problem with the shoes because it has an LED issue or not? By that, I mean, do you experts think it may be a problem with the power source? because I don't want to buy shoes I cant successfully mod.
Here's the link: http://www.aliexpress.com/item/EMS-...-the-dark-back-to-the-future/32501394132.html
Thanks and have a nice day,
TJ Jordan
 
You must log in or register to reply here.

Similar threads

rebel86
BullAirs Nike Air Mag Bag Capsule Case Limited to 100
Replies
7
Views
1,196
SlyFox
SlyFox
Grey Area
Back To The Future 2 Hoverboard
Replies
15
Views
564
Grey Area
Grey Area
barrie
HELP BACK TO THE FUTURE STEAM TRAIN PLANS OR DRAWINGS
Replies
2
Views
663
barrie
barrie
TerranCmdr
Terran's Ghostbusters builds (costumes, props, and RC cars oh my!)
Replies
8
Views
853
TerranCmdr
TerranCmdr
XatD26
Need some help with sizing Headgoonie BTTF Marty McFly jacket.
Replies
6
Views
505
emmetguy222
emmetguy222
Back
Top