Done / Completed DREDD 3D Lawgiver kit by morganthirteen & joatrash (OPEN))

Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

Finally got approval from the finance department to order mine. I'll be installing a BlasterCore into mine along with my custom sound fonts and LED indicators. PM sent to Joe on the order.
 
Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

Curious... Where are all the finished builds? Show off your Lawgivers!!!!
 
Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

Still procrastinating with mine.


Could someone point me towards the cog print out for the clip. I went back through the thread and have most likely missed It. please and thanks...
 
Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

Planning.....

1382325_642451229122875_602885462_n.jpg
 
Last edited:
Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

Yes, you can still get a kit. PM for details.
 
Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

Guessing the real ones might be dangerous if you fall into a fire for some reason!
 
Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

Yes, I'm not going to use real ammo. Created some faux rounds. Here are some progress shots. They still need some sanding, tapering, and polishing. I need to make two more. Once they are all good. I'll put them inside the clip permanently. I just need to test the weight and drill them out if they are still too heavy. They are much lighter than the real ammo and only slightly heavier than the resin ammo.

1013588_645102595524405_1887246160_n.jpg


1382870_645102592191072_1457512388_n.jpg
 
Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

More progress...
1375879_646551945379470_1929020883_n.jpg


Made the bullets too long, got to shorten them by about 1/8".
 
Last edited:
Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

Bumping this 'cause we are still doing them. Here's what it looks like with an HJQ display installed!

 
Last edited by a moderator:
Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

I'll be interested eventually. In the video above, is that a hollow or modified solid cast ?
 
Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

I used a rotocast version for the display.
 
Re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (Briefly open again!!))

excellent thanks. I had sourced my screens literally months ago when you and I talked about LG electronics. Now my cast is ordered, I'll write up some code. Expect a screen + sound version... in the future !
 
re: DREDD 3D Lawgiver kit by morganthirteen & joatrash (OPEN))

Bump to the top. Reel Images is doing another run of leathers, and those leathers need a proper Lawgiver to accompany them!
 
This thread is more than 4 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

Similar threads

Astyanax
Done / Completed NERF SCOUT TROOPER BLASTER Conversion Kit by Astyanax & AnubisGuard
Replies
14
Views
887
Astyanax
Astyanax
Bubuks Garage
The Starkiller: Open Hatch Lightsaber Run 2024
Replies
0
Views
187
Bubuks Garage
Bubuks Garage
Indy Magnoli
Limited Run Neverending Story AURYN medallion by Magnoli Props
2
Replies
31
Views
1,282
scud42
scud42
Props3D
Limited Run Dredd Lawgiver 2012 Full Electronics and Action
14 15 16
Replies
309
Views
27,437
mikepasquale
mikepasquale
Kokanee
Limited Run SNW Phaser "Big Damn Hero" Kit Phase II
Replies
8
Views
627
Kokanee
Kokanee
Back
Top