Mara Jade's Father
Master Member
Not a clear image but Kurtyboy had an image posted: http://www.therpf.com/showthread.php?t=230129&page=9&p=3525151&viewfull=1#post3525151
Last edited by a moderator:
DL-44 ESB Blaster Discussion - Greeblies POST 208
- Thread starter Boba Debt
- Start date
Not a clear image but Kurtyboy had an image posted: http://www.therpf.com/showthread.php?t=230129&page=9&p=3525151&viewfull=1#post3525151
newmagrathea
Sr Member
Those pics are better than the ones that I have.
Boba Debt
Master Member
Judging by this picture, if you go with 2 they would be touching or almost be touching in the middle
...... Luke's Bespin blaster, only a single retainer during filming (and quite possibly the second retainer and a motor coil were originally glued on but fell off).
Mara Jade's Father
Master Member
Re: DL-44 ESB Blaster Discussion - Scope Bracket NUTS POST 173
Boba Debt, I think the image you posted a while back..
...shows proper placement of the left one (and right if there was one to begin with) when compared to the image in the Kurtyboy post.
Boba Debt, I think the image you posted a while back..
...shows proper placement of the left one (and right if there was one to begin with) when compared to the image in the Kurtyboy post.
Try buffing that. Steel wool or a scotch pad, or something softer. There's a point between fresh blackening and stripping it where it looks nice and satiny! Also I used perma blue instead of AB
as for the distributor rings, when they're placed close together they almost look like one unit! If that was on purpose, it's clever.
See. That's what happens when you do things with a gimpy finger. Just kidding, buddy.
its almost healed, got the splint off friday morning. more X-rays everything still attached, now all it is is bleeding and just very little swelling, cant wait for this to be over
:thumbsup
looking for some more advice guys.
so i ditched the aluminum black idea. i ended up steel wooling it all off and painted it with the blacks boba debt suggested
with it coming out too new looking i did what mara jades father suggested and used wd40 and some old tshirts and rubbed the new finish
what i got was exactly what i was hoping for, BUT i have some serious pitting from the denix in 1 spot
i don't know if i should strip all the paint off and then use a dremel with some polishing stones to smooth and start over
or if i should scruff it all up and use some filler to fill the pits
what do you guys think?
Sent from my iPhone using Tapatalk
so i ditched the aluminum black idea. i ended up steel wooling it all off and painted it with the blacks boba debt suggested
with it coming out too new looking i did what mara jades father suggested and used wd40 and some old tshirts and rubbed the new finish
what i got was exactly what i was hoping for, BUT i have some serious pitting from the denix in 1 spot
i don't know if i should strip all the paint off and then use a dremel with some polishing stones to smooth and start over
or if i should scruff it all up and use some filler to fill the pits
what do you guys think?
Sent from my iPhone using Tapatalk
thanks tom. the glazing putty i've been using covers good and hides well with paint.
i wouldn't mind it if it was little bit smaller, it would actually look great if it were the size of a nickel or quarter. but it's fairly large...
Sent from my iPhone using Tapatalk
i wouldn't mind it if it was little bit smaller, it would actually look great if it were the size of a nickel or quarter. but it's fairly large...
Sent from my iPhone using Tapatalk
Mara Jade's Father
Master Member
Similar threads
