I have 2 sets I’m trying different ways to get the desired look,You have any extra of those send them my way!
i will see what I have left, my cousin who cut these for me at his work place is getting a new £300 thousand pound laser cutter in December and he says he will try and cut me some better ones, so I should have some spares, time will tellI’ll take rejects
could you please explain the salt water etching to me that I haven’t heard of that oneA couple of home made "Twin" Sabers. Made from a few different diameters of tube (aluminium aerial masts etc), the widest being 1.5" and some greeblies. The switch boxes were cut from aluminium billet with a hacksaw. No special tools unfortunately, a bench vice, hand drill, , dremel, files and tap&die set was about all that I had access too. Some parts (the middle section) were saltwater etched using an xbox 360 power supply. The pommels are some motorcycle bar ends - thanks to the idea in this thread.
https://farm5.staticflickr.com/4495/37997161526_8a0aef63ee_c.jpg
https://farm5.staticflickr.com/4509/37341249004_5a10e2c70e_c.jpg
https://farm5.staticflickr.com/4506/37997147676_6e22501104_c.jpg
For saltwater etching I followed ARKM's guide a few years ago and have made a few saber hilts using the method since. It's a great guide. http://forums.thecustomsabershop.com/showthread.php?13430-ARKM-s-Saltwater-Etching-Tutorialcould you please explain the salt water etching to me that I haven’t heard of that one
where did you get your light source from ?
nice build
For saltwater etching I followed ARKM's guide a few years ago and have made a few saber hilts using the method since. It's a great guide. http://forums.thecustomsabershop.com/showthread.php?13430-ARKM-s-Saltwater-Etching-Tutorial
For the light source I used a single cree XPE2 Royal Blue in one if the sabers and a Tri-Cree XPE2 blue LED for the other. Both powered with an 18650 battery with a 1ohm resistor and latching switch for the most basic stunt set-up.
I intend to upgrade the single LED to a triple at some point. I only really built these sabers as I recently ordered a Photon Blade and didn't have a blue LED saber around, so this way I could test Royal blue, standard blue, single and triple LEDs with the new blade.
your only up the road from me, your a Yorkshire lad, I’m a Lancashire lad, another question if you don’t mind, where did you get the light tubes from ?A couple of home made "Twin" Sabers. Made from a few different diameters of tube (aluminium aerial masts etc), the widest being 1.5" and some greeblies. The switch boxes were cut from aluminium billet with a hacksaw. No special tools unfortunately, a bench vice, hand drill, , dremel, files and tap&die set was about all that I had access too. Some parts (the middle section) were saltwater etched using an xbox 360 power supply. The pommels are some motorcycle bar ends - thanks to the idea in this thread.
https://farm5.staticflickr.com/4495/37997161526_8a0aef63ee_c.jpg
https://farm5.staticflickr.com/4509/37341249004_5a10e2c70e_c.jpg
https://farm5.staticflickr.com/4506/37997147676_6e22501104_c.jpg
Eh up lad ! ( nice ) Does tha know I was also drawn to the blue one, stunning colour, I’m nipping down to Maplins over t weekend and have a gander at what they have, you’ve made me want to put a light in and put a blade on it now ya bugger ! May be have a butchers for a bladeEh up lad!
There’s not many options for Lightsaber blades for us in the UK, but I get mine from JQsabers (they’re based in Wales). I believe they’re the same as the Vader’s vault blades. I’m loving the Photon Blade with the tri-cree blue.
had a look on the website last night, not bad prices, I still love the blue but green is amazing and growing on meThis might sound strange, but the blue blade in the photo's above is the single royal blue LED and the green blade is the triple blue LED.
The photon blade is a specially pigmented blade that reacts with blue light to produce an awesome green glow.
The below picture is the same light source, one with a standard blade and the other with the photon blade.
https://farm5.staticflickr.com/4523/38067902706_7a709ac994_c.jpg
Just wanted to show off my saber I built this years ago based on the Big Yellow Box saber III design. Someone on the A.S.A.P. boards influenced the gold highlighting. The grips are from the AOTC Anakin saber. This is the only picture of it that I have. I sent it to a machinist years ago to have it made from aluminum and he lost the saber.
View attachment 666631
Anyone built a saber from the cheaper Graflex or another flash?
https://i.ebayimg.com/images/g/YxMAAOSw-29ZPMIY/s-l300.jpg
Anyone built a saber from the cheaper Graflex or another flash?
https://i.ebayimg.com/images/g/YxMAAOSw-29ZPMIY/s-l300.jpg
there is one double blade saber made of two of these earlier on that thread that is awesome!