New BMF coming

What scale does he work out being TG?........what would his head dimensions be for e.g.?

J
Tony is going to help me get the scale right...gotta figure since he made the cockpit, it's gonna be right :)..That being said..I don't have any end result sizes yet.
Normally when you make a model in 3d, you use something called smoothing groups which makes the model LOOK smooth, when it is not. For 3d printing I need to just have a ton of faces so it doesn't look all choppy...so I am doing some stuff that will work better for adding faces as my 1st pass had some rough spots.....I'm sure I've overkilled the details for how small it is..but then again...we will see :) I am really curious how much of the details will be there... Will be a surprise for me as well! :)
 
Tony is going to help me get the scale right...gotta figure since he made the cockpit, it's gonna be right :)..That being said..I don't have any end result sizes yet.
Normally when you make a model in 3d, you use something called smoothing groups which makes the model LOOK smooth, when it is not. For 3d printing I need to just have a ton of faces so it doesn't look all choppy...so I am doing some stuff that will work better for adding faces as my 1st pass had some rough spots.....I'm sure I've overkilled the details for how small it is..but then again...we will see :) I am really curious how much of the details will be there... Will be a surprise for me as well! :)

TronGod!

For the Hasbro, the approximate height of Solo is -from head to ass :p-, 21 mm, more or less, maybe 21.5.
Make it like this. If necessary I will refine the size.

Good job!

P.D.: We will need, Solo, Chewie, C3PO...
 
More upgrades:

Hasbro Cabin Door.

Already at my shop, fresh and ready! :cool


MILLENNIUM FALCON HSBRO CABIN DOOR.jpg



Many thanks for your support!
 
Thank you for all the comment . tony that is cool I will get one when I order the cockpit. :thumbsup
 
  • Like
Reactions: FZ6
Hi Tony,

I was just wondering if it is possible to make the Floor grilles of the Main Room, I have been searching the net and could not find anything that would match.

It can be made a half A4 size and can be cut to fit to size....

View attachment 433777

Glad to help out here!!

Who was the guy that asked me these floor grilles?... :D:D

MILLENNIUM FALCON HASBRO FLOOR GRILLES.jpg

I've made a set of 12 grilles, measuring in total 7 x 8 cm approx.

Just search on the Falcon HSBRO section for Floor Grille.

If you need more grilles, I can upgrade the file including more in, just for saving some bucks.

Many thanks for your support!!!

:cool
 
I like that idea the falcon will be more safer on the wall then a flour stand for now the stand will doo

thank you
 
Glad to help out here!!

Who was the guy that asked me these floor grilles?... :D:D

View attachment 436962

I've made a set of 12 grilles, measuring in total 7 x 8 cm approx.

Just search on the Falcon HSBRO section for Floor Grille.

If you need more grilles, I can upgrade the file including more in, just for saving some bucks.

Many thanks for your support!!!

:cool

Hi Tony, thank you very much for the floor tiles! Great upgrade! Now my interior will look more like the original..

I did a quick measurement on my model... Can you add a little bit more? My size is 10 cm x 14 cm...is it still possible? I will buy two because im doing the rear engine bay too.. Thanks again...
 
Hi Tony,

I saw you are doing the corridor as well for the main entrance one, can you also design one which is just a 90 degree sweep tube?
 
Hi Tony, thank you very much for the floor tiles! Great upgrade! Now my interior will look more like the original..

I did a quick measurement on my model... Can you add a little bit more? My size is 10 cm x 14 cm...is it still possible? I will buy two because im doing the rear engine bay too.. Thanks again...

OK. No problem.

Already at the shop a second version with 20 tiles, instead of 12. Is the maximum file size allowed. I can't add more tiles!!!
Your Hasbro will look gorgeous!!!

:thumbsup

- - - Updated - - -

Hi Tony,

I saw you are doing the corridor as well for the main entrance one, can you also design one which is just a 90 degree sweep tube?

I need to know more details. If you can draw a simple design and send it to me or post it here. OK?
 
Last edited:
There is no such frowning allowed here, especially on your own thread.
This crazy toy is bringing out so many lurkers and no matter how basic the question, just ask, I do, I'm a newbie to this level of modeling even though I've been making stuff for ever.

This is the place :)

Thanks spacebob.

I'm constantly amazed (and educated) by keeping up with the amazing work you guys do.
 
Make the corridor Cinderella,..

Fix the floor tiles Cinderella, :)


Sorry, I could not resist.

I am more guilty then most as I have asked poor Tony to make a lot.
 
  • Like
Reactions: FZ6
OK. No problem.

Already at the shop a second version with 20 tiles, instead of 12. Is the maximum file size allowed. I can't add more tiles!!!
Your Hasbro will look gorgeous!!!

:thumbsup

- - - Updated - - -



I need to know more details. If you can draw a simple design and send it to me or post it here. OK?


Hi Tony! Many many thanks, I just bought 2 panels off Shapeway the big one & small one, hope it gets heres as soon as possible.

Yeah Jameth, I'm quite guilty of requesting too much out of Mr. Tony....I just thought that since he was doing the main entrance corridor already, it would just easy to copy the panels to make a 90 degree sweep, in which interior modelers like myself can modify to heart's content...LOL!

Anyway below is the idea ,,,if it is possible only...

YoDJBEE.jpg

To add additional functionality so viewers can see the inside, I suggest that the Upper Right Quadrant (Top/Outer section) be removable and printed as a separate part within the set piece.
Corridor opening.jpg
 
Last edited:
  • Like
Reactions: FZ6
Make the corridor Cinderella,..

Fix the floor tiles Cinderella, :)


Sorry, I could not resist.

I am more guilty then most as I have asked poor Tony to make a lot.

Hahahahaha!!!

I have to design your cone with side console. You're in my -big- list too!

About the pits, this will get some more time to do it!


Cinderella

- - - Updated - - -

Hi Tony! Many many thanks, I just bought 2 panels off Shapeway the big one & small one, hope it gets heres as soon as possible.

Yeah Jameth, I'm quite guilty of requesting too much out of Mr. Tony....I just thought that since he was doing the main entrance corridor already, it would just easy to copy the panels to make a 90 degree sweep, in which interior modelers like myself can modify to heart's content...LOL!

Anyway below is the idea ,,,if it is possible only...



To add additional functionality so viewers can see the inside, I suggest that the Upper Right Quadrant (Top/Outer section) be removable and printed as a separate part within the set piece.

I see. As soon as I get some more time I will design this 90º tube. No problem.

:unsure :p
 
Back
Top