Done / Completed Done

TheRocketeer

TheRocketeer

Master Member
Its about time I start a thread on this cowl/helmet.

The model is as screen accurate as you can get.. it is modeled and being printed now.

It will be cast in semi ridged resin for 22.25" heads and Rubber to fit a 24" heads, designed to be a close fit like the show.

Cost will be $254usd + shipping and I will offer finishing work for an extra $200usd

Here is a couple renders of the helmet...it is being printed now. I'll update the thread when the print is done :) please post interest

image.jpegimage.jpeg

And the print :)

Front.jpgSide.jpg
 
Last edited:
Re: DareDevil Season 2 cowl/helmet from 3D print

I'm interested. Would of course like to see it when you have it completed, but looks great so far!
 
Re: DareDevil Season 2 cowl/helmet from 3D print

You already know I am interested :)

Eager to see it printed. I will likely pay you to finish it, too. :D
 
Re: DareDevil Season 2 cowl/helmet from 3D print

OK.. depends if theres enough interest.. I will finish the master up though..
mikekal said:
I'm interested. Would of course like to see it when you have it completed, but looks great so far!
Click to expand...

On the list :) print pics coming soon :)
EastviewBeast said:
You already know I am interested :)

Eager to see it printed. I will likely pay you to finish it, too. :D
Click to expand...

Added :)
JBReplicas said:
This is awesome, please add me to the list :cool
Click to expand...

Counted in sir :)
BROTHERFOSTER said:
Count me in. Interested.
Click to expand...

On the list
mbmcfarland said:
Interested!

Sent from my XT1254 using Tapatalk
Click to expand...

Thanks, modeling is only a small part of the process :) on the list
Cree said:
Interested for sure!
Great job on the modelling.
Click to expand...

Alright :)
PcFish said:
Yep, I'm definitely Interested!
Click to expand...
 
Re: DareDevil Season 2 cowl/helmet from 3D print ***Print pics ***

Hmm...I'm about to start working on one of these for myself. You say it's for a 24" head...i have a 23" melon. Any chance you would sell the model for me to scale down and print myself? PM me if you would rather discuss that way.

Thanks!
 
Re: DareDevil Season 2 cowl/helmet from 3D print ***Print pics ***

On the list :)
mikekal said:
Yes, please:)
Click to expand...

Well I would say 24" head max.. I have a 22.5" and it should fit me well.. It will be a flexible resin or a hard rubber..not sure which. I believe in the show its a 2 piece helmet to be a hard shell and fit that tight

IronManiac said:
Hmm...I'm about to start working on one of these for myself. You say it's for a 24" head...i have a 23" melon. Any chance you would sell the model for me to scale down and print myself? PM me if you would rather discuss that way.

Thanks!
Click to expand...
 
This thread is more than 3 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

Similar threads

S
Done / Completed Done
2
Replies
23
Views
2,109
CivilizedAge
CivilizedAge
S
Done / Completed done
3 4 5
Replies
91
Views
11,261
lebz
lebz
S
Limited Run Done
2 3
Replies
54
Views
5,734
Spirit of ob1
S
JKKS
Limited Run Daredevil Season 3 Mask Final Run - DONE
2
Replies
22
Views
4,203
unbreakable737
U
S
Done / Completed Done 5-10-21
4 5 6
Replies
112
Views
13,040
Spirit of ob1
S
Back
Top