Blaster builds, Boba Fett finished, Leia, Greedo, Jabba, DH-17, Kylo Ren

Ok, I nearly didn't bother to finish this as it was turning in to a PITA with all the masking off :lol

I'll be honest it's a bit more rushed & sloppy than I'd like & I went way too thick with the Gloss white on one side

looks ok (at a distance) decided to weather it slightly

still think ink it's a shame these are small especially when Nerf guns are usually a good size

I think if anyone ends up doing 1-1 scale kits of this Blaster it would be best if the White & black parts were seperate to make painting easier
 

Attachments

  • image.jpg
    image.jpg
    745 KB · Views: 77
  • image.jpg
    image.jpg
    720.2 KB · Views: 65
  • image.jpg
    image.jpg
    534.6 KB · Views: 75
  • image.jpg
    image.jpg
    599.7 KB · Views: 69
  • image.jpg
    image.jpg
    359.4 KB · Views: 72
  • image.jpg
    image.jpg
    430.3 KB · Views: 67
  • image.jpg
    image.jpg
    392.4 KB · Views: 64
  • image.jpg
    image.jpg
    396.6 KB · Views: 70
Needed to make some progress on something :lol

I've had the parts sat on my shelf for a while so decided to try & put it together at last

I glued a pen lid in to the body of the blaster for the barrel to slide over & hopefully help it stay in place

had a bit of a time trying to glue the barrel on straight

the Tomtit cylinder just slid over the barrel

just need to stick down the squares & weather it now
 

Attachments

  • image.jpeg
    image.jpeg
    399.1 KB · Views: 83
  • image.jpeg
    image.jpeg
    335.8 KB · Views: 108
  • image.jpeg
    image.jpeg
    419.6 KB · Views: 86
Lightly weathered the ROTJ Leia & I think it's done

the rubber squares were just some generic ones from eBay

I really do love these Rubies Blasters :)
 

Attachments

  • image.jpeg
    image.jpeg
    365.3 KB · Views: 116
  • image.jpeg
    image.jpeg
    233.6 KB · Views: 102
  • image.jpeg
    image.jpeg
    254.8 KB · Views: 103
  • image.jpeg
    image.jpeg
    555.6 KB · Views: 101
  • image.jpeg
    image.jpeg
    333.8 KB · Views: 99
  • image.jpeg
    image.jpeg
    820.3 KB · Views: 107
  • image.jpeg
    image.jpeg
    722 KB · Views: 105
  • image.jpeg
    image.jpeg
    883.7 KB · Views: 118
Very cool.

Being new to the prop thing, have to ask: did this start out as one of those white and orange Rubies guns?

Sent from my SM-G360V using Tapatalk
 
Lightly weathered the ROTJ Leia & I think it's done

the rubber squares were just some generic ones from eBay

I really do love these Rubies Blasters :)
Country paul, I have a few questions since your ROTJ ddc is the best I've seen. Is that satin or gloss that you did on the grips? I also searched the earth for the rubber bumpons you got but can not find them. Yours are the closest I've seen. I'm hoping the ones I ordered are close but its hard to tell. I've finished everything but painting this thing. I made my own squares but after seeing yours I'm taking mine off.
20200415_025802.jpg
 
This thread is more than 4 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top