Limited Run Avengers: Age of Ultron/Civil War Captain America Belt and Harness Run

Re: Avengers: Age of Ultron Captain America Belt Buckle

Good news! The first part of the molds are done, I just need to pour the second part for the bottoms. Once that is done these will be ready to go.
 
Re: Avengers: Age of Ultron Captain America Belt Buckle

Here we go! Buckle's are finally done (along with extras!)

I partnered up with @starlordquill to finish up not just the buckles for Age of Ultron and Civil War, but also all the other belt and harness hardware. Everything was modeled, 3D printed, and mastered, then molded. I started pulling test casts today, and we're very happy with everything.

12027527_10152959929716862_8345345865806654808_n.jpg


12039406_10152959929756862_906199528405949959_n.jpg


First pulls of a few of the items all polished up! With that said, we're going to open up the run. Robbie and I are offering up a few options. You can purchase cold cast aluminum belt and harness hardware, or full belts and harnesses. We are doing both Age of Ultron and Civil War pieces.

Cost for belt hardware is $60
Cost for harness hardware is $40
Cost for belt AND harness hardware is $90
Gauntlet magnets (set of 4) is $25

The belts and harnesses will be made with genuine leather and canvas/cotton webbing.
Fully finished belts will be $250
Fully finished harnesses will be $150
Both belt and harness can be bundled at a discount for $350

We also have a mold for the shoulder A's seen on the Age of Ultron and Civil War costumes.
Cost is $10 for a raw pair or $25 for a finished pair

If you're interested, note what you want and we'll get you the payment details.

**Please note, we will try to get through these as quickly as we can, but cannot guarantee Halloween delivery for all orders
 
Last edited by a moderator:
If I ordered just some of the cast pieces and shoulder A's (fully finished) immediately, and not the belt or harness, would you be able to have just those ready before Halloween?

Thanks, and great work!
 
Last edited:
Warmachine2000 said:
i have one of Phebert"s aluminum shields, Would this be able to act as a working harness which could hold the shield? thanks
Click to expand...
It will be able to support the weight (assuming that his shields weigh the same as most aluminum shields). However, we will not be including any magnet system. Also mind that it is resin so you will want to add some felt or foam ontop of the magnet on the shield to prevent it from slamming directly into the back buckle.

Sent from my XT1254 using Tapatalk
 
Payment has been sent.

By the way, I tried to send you the confirming message Starlord, but it says your inbox is full and you can't accept any more messages until its cleared!
 
Thanks for all the interest so far! I've been working on casting pieces to fulfill orders. We are doing this run here as well as on Facebook, so keep the patience and we'll get everything sorted out as soon as we can!

Robbie will be sending out his belt and pouches this week for stitching and attaching, so more progress pics to come!
 
This thread is more than 7 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

Similar threads

NewmanAssembles
Service High Quality Captain America Shield Replicas
Replies
0
Views
667
NewmanAssembles
NewmanAssembles
ToddsCostumes
NEW INDY SHIRT RUN
Replies
0
Views
265
ToddsCostumes
ToddsCostumes
Bubuks Garage
The Starkiller: Open Hatch Lightsaber Run 2024
Replies
0
Views
214
Bubuks Garage
Bubuks Garage
B
Interest OT Split Plug Run
2
Replies
30
Views
1,855
Davy Jones
Davy Jones
thorssoli
Unlimited Run Captain Enoch Helmet Kits
Replies
10
Views
1,551
thorssoli
thorssoli
Back
Top