Tanolucas
Active Member
Hello people.
With this vehicle in particular, it happened to me the opposite that with the jakku speeder, in this case, I did not like at all the first time I saw it, I considered it a poorly achieved vehicle, as with lack of detail and made at hurried. The days passed and every so often I looked for new information about the movie. Searching, I found an article that compared this vehicle with the Ford Falcon 60 ............. In short, this article made me start to see this vehicle with more "love" ... so , after looking at a few more photos, I ended up changing my first impression completely and decided to make mine from scratch.
The vehicle that everyone must have already seen ...
First basic computer forms to determine proportions and distances
Some progress on the cockpit, which I will gradually detail.
Advance on the turbine that this device has on the left side, look to make it as similar as possible to the little you can see in the photos that are on the network.
I started with that kind of afterburner that has the end.
Then I went to the front of the turbine ..
Finally, I detail the middle part ..
In the end, take the opportunity to give a little more detail to the back ..
Before
After.
I made the seats with their head supports and that kind of small ailerons that is behind each seat.
Everything together ... is taking shape !! ..
Advances, for now everything in Computer
Front part
This is the side turbine on the left side
More detail about the interior of the cockpit. I am designing it in such a way that I can place lights, so it is necessary to take into account where the cables will go, where the lights will go, etc., etc.
I made the engine that has on the front, to my understanding, a kind of electric generator.
The windshield and its corresponding frame, this piece was quite complicated due to its intricate shape ..
These are the components that are uncovered in the left part of the vehicle, still lack more detail, but these are the most striking forms
the paneling, which is quite complicated, the shapes in the front are asymmetrical and do not have a logic
Now I dismiss the virtual part with the complete design and ready for printing in these renders.
A couple more with the lighting of the film .....
Now, the important thing, printed pieces
Seccion 1
Seccion 2
Together
Aileron
The windshield frame
That's all folks. Soon I will continue printing the pieces
Cheers!
With this vehicle in particular, it happened to me the opposite that with the jakku speeder, in this case, I did not like at all the first time I saw it, I considered it a poorly achieved vehicle, as with lack of detail and made at hurried. The days passed and every so often I looked for new information about the movie. Searching, I found an article that compared this vehicle with the Ford Falcon 60 ............. In short, this article made me start to see this vehicle with more "love" ... so , after looking at a few more photos, I ended up changing my first impression completely and decided to make mine from scratch.
The vehicle that everyone must have already seen ...
First basic computer forms to determine proportions and distances
Some progress on the cockpit, which I will gradually detail.
Advance on the turbine that this device has on the left side, look to make it as similar as possible to the little you can see in the photos that are on the network.
I started with that kind of afterburner that has the end.
Then I went to the front of the turbine ..
Finally, I detail the middle part ..
In the end, take the opportunity to give a little more detail to the back ..
Before
After.
I made the seats with their head supports and that kind of small ailerons that is behind each seat.
Everything together ... is taking shape !! ..
Advances, for now everything in Computer
Front part
This is the side turbine on the left side
More detail about the interior of the cockpit. I am designing it in such a way that I can place lights, so it is necessary to take into account where the cables will go, where the lights will go, etc., etc.
I made the engine that has on the front, to my understanding, a kind of electric generator.
The windshield and its corresponding frame, this piece was quite complicated due to its intricate shape ..
These are the components that are uncovered in the left part of the vehicle, still lack more detail, but these are the most striking forms
the paneling, which is quite complicated, the shapes in the front are asymmetrical and do not have a logic
Now I dismiss the virtual part with the complete design and ready for printing in these renders.
A couple more with the lighting of the film .....
Now, the important thing, printed pieces
Seccion 1
Seccion 2
Together
Aileron
The windshield frame
That's all folks. Soon I will continue printing the pieces
Cheers!
Last edited: