-
Welcome to the Project Runs Forum!
This forum is intended for interest gauging and active runs. Due to the transient nature of this forum, please keep all research and ongoing discussion in one of our main forums so your information is not lost.
Only Premium Members can start a new run.
Limited Run ROTJ Jabba's Palace Guard Blaster DL-18 Parts - Spares Available!
- Thread starter Corellianexports
- Start date
Re: Jabba's Palace Guard Blaster "Mos Eisley Special" Parts
All parts shipped. Run completed.
All parts shipped. Run completed.
Re: Jabba's Palace Guard Blaster "Mos Eisley Special" Parts
I will be starting a new run of these parts this weekend. If any one is interested in getting a set please send me a pm or post a reply. Thanks.
I will be starting a new run of these parts this weekend. If any one is interested in getting a set please send me a pm or post a reply. Thanks.
Re: Jabba's Palace Guard Blaster "Mos Eisley Special" Parts
I have updated the waiting list.
I will start machining today.
I will also be working on an aluminum scope prototype. Once it is complete, I'll post a price. It's a fairly simple part, so I'm not expecting the price to be high (more than $150).
I have updated the waiting list.
I will start machining today.
I will also be working on an aluminum scope prototype. Once it is complete, I'll post a price. It's a fairly simple part, so I'm not expecting the price to be high (more than $150).
All parts have been cut out and machining has begun.
The waiting list has been updated.
The waiting list has been updated.
Waiting list updated.
It looks like in addition to the scope, there is a scope mount so if anyone is interested in that part just post a reply or send me a pm.
We've got a major heat wave hitting Oregon this week so the machining is probably going to slow down a little.
I did get some machining accomplished this evening, though.
It looks like in addition to the scope, there is a scope mount so if anyone is interested in that part just post a reply or send me a pm.
We've got a major heat wave hitting Oregon this week so the machining is probably going to slow down a little.
I did get some machining accomplished this evening, though.
JetSetWilly
Well-Known Member
Interested in scope and mount. Cheers
Waiting list updated.
The list is full at this point, but if anyone else is interested in parts, feel free to post a reply and I'll
start a new list for another run. Thanks.
The list is full at this point, but if anyone else is interested in parts, feel free to post a reply and I'll
start a new list for another run. Thanks.
Photos are pending. I'll be working on a blueprint for the scope and mount next week.
From the reference photos I've looked at so far, the mount is basically a rectangular part and probably grooved.
Also, it looks like the scope has a very small piece attached to the front of it which may have broken off during filming.
This is a reproduction that has the missing part. Did everyone want this part included on the scope?
Here is a close up:
From the reference photos I've looked at so far, the mount is basically a rectangular part and probably grooved.
Also, it looks like the scope has a very small piece attached to the front of it which may have broken off during filming.
This is a reproduction that has the missing part. Did everyone want this part included on the scope?
Here is a close up:
Waiting list updated.
The side parts are about 50% completed. The larger pieces should be mostly completed tonight. I'll start machining the small pieces later this week.
The side parts are about 50% completed. The larger pieces should be mostly completed tonight. I'll start machining the small pieces later this week.
The large parts are done and the small parts are 50% complete. I should have the side parts completed by the end of next week.
The following week, I'll start machining the scope and mount prototypes.
Resin scopes/mounts may be easier to make and lower priced so I will post some price options in a couple of weeks
for aluminum and/or resin scope parts.
The following week, I'll start machining the scope and mount prototypes.
Resin scopes/mounts may be easier to make and lower priced so I will post some price options in a couple of weeks
for aluminum and/or resin scope parts.
Similar threads
