drumguy560
Well-Known Member
Hey all, decided to post this in the Marvel forum too (it also appears in the project run forum) so that non-premium members could check it out.
Sales WILL NOT be discussed here, if you want to buy, get a premium membership and go to the project run forum!
here we go!
Here's some detailed pictures of it.
The helmet is made to be 100% screen accurate, as demonstrated by it's many removable pieces.
You can see below that the outer mouth piece is removable
This is correct as the movie version. They made many different helmets for the movie. For the scenes where the faceplate was opened, they removed the outer mouthpiece, as seen in THIS screenshot
In addition, the main mouthpiece is completely detachable from the mandibles, and are connected via a snap-fit connection to them. In addition, the wiring features a quick-disconnect JST style connector so the mouthpiece can be completely removed, as in this photo,
Alternatively, you may leave one side connected, in order to get the helmet on, as in this picture
which mimics the movie version, as shown in THESE images
In addition to allowing you to put the helmet on, having the mouthpiece dropped like this is a nice way to get yourself some fresh air during a long convention!
As you can see in THIS picture, the helmet is fully lit with red LEDs
The faceplate is also detachable via two screws on each side. It's lights are connected via a JST connector just like the mouth.
For reference, here is a comparison shot between the movie helmet and mine.
(screen used helmet from D23) and mine 
The faceplate and mandibles are fully motorized, as seen in THIS GIF
As you can see, you DO have to help the mandibles down. This is due to a limitation in the laws of physics regarding motor size and torque. There is not much room in the helmet for motors and electronics. I got the absolute largest, and most powerful motors that would fit, but they are not quite strong enough to pull against the elastic in the mouth. However, once you help it down, it stays down quite well. To activate the helmet, the red square buttons on the helmet are used. The button on the right operates the faceplate, and the button on the left operates the LEDs. The LEDs are powered on a separate circuit from the faceplate and mandibles. This is to save precious battery power for the motors. The motors are powered by THESE electronics
There are two Faulhaber geared, encoded DC motors with right angle shafts, an Adafruit PowerBoost 1000c, and a 1200mah lipoly battery. The battery can be charged via a standard micro usb cable, and can be accessed through the front of the helmet to charge. The LEDs are powered by a standard CR2032 battery. The helmet is totally "dumb", meaning that there are no control electronics. The faceplate falls down with gravity when the motors are deactivated.
The helmet is also made in primarily semi-flexible materials, as per the movie one, as seen here
compared to mine 
This assists greatly when putting on the helmet, as you can stretch it out to fit over the ears, and then re-position it until it is comfortable.
The helmet is assembled using almost entirely screws. Very little glue is used.
Here is what the helmet looks like when on
(normally the outer mouthpiece would be removed when the faceplate is up)
Sales WILL NOT be discussed here, if you want to buy, get a premium membership and go to the project run forum!
here we go!
Here's some detailed pictures of it.
The helmet is made to be 100% screen accurate, as demonstrated by it's many removable pieces.
You can see below that the outer mouth piece is removable
This is correct as the movie version. They made many different helmets for the movie. For the scenes where the faceplate was opened, they removed the outer mouthpiece, as seen in THIS screenshot
In addition, the main mouthpiece is completely detachable from the mandibles, and are connected via a snap-fit connection to them. In addition, the wiring features a quick-disconnect JST style connector so the mouthpiece can be completely removed, as in this photo,
Alternatively, you may leave one side connected, in order to get the helmet on, as in this picture
which mimics the movie version, as shown in THESE images
In addition to allowing you to put the helmet on, having the mouthpiece dropped like this is a nice way to get yourself some fresh air during a long convention!
As you can see in THIS picture, the helmet is fully lit with red LEDs
The faceplate is also detachable via two screws on each side. It's lights are connected via a JST connector just like the mouth.
For reference, here is a comparison shot between the movie helmet and mine.
The faceplate and mandibles are fully motorized, as seen in THIS GIF
As you can see, you DO have to help the mandibles down. This is due to a limitation in the laws of physics regarding motor size and torque. There is not much room in the helmet for motors and electronics. I got the absolute largest, and most powerful motors that would fit, but they are not quite strong enough to pull against the elastic in the mouth. However, once you help it down, it stays down quite well. To activate the helmet, the red square buttons on the helmet are used. The button on the right operates the faceplate, and the button on the left operates the LEDs. The LEDs are powered on a separate circuit from the faceplate and mandibles. This is to save precious battery power for the motors. The motors are powered by THESE electronics
The helmet is also made in primarily semi-flexible materials, as per the movie one, as seen here
This assists greatly when putting on the helmet, as you can stretch it out to fit over the ears, and then re-position it until it is comfortable.
The helmet is assembled using almost entirely screws. Very little glue is used.
Here is what the helmet looks like when on
