ninjacentaur
Member
I am starting to Work on a Foam Irom Man Suit. I started a while back but my printer stopped working. All i have are the Handplates.
Iron man MKVII Pepakura Costume
- Thread starter ninjacentaur
- Start date
ninjacentaur
Member
I am going to try to finish before Halloween
ninjacentaur
Member
Thanks guys. I have made serious progress (didn't quite finish by Halloween) I would post pictures but don't have any.
Sent from my KFOT using Tapatalk
Sent from my KFOT using Tapatalk
ninjacentaur
Member
All I have left is the right shin piece and the left thigh.
Sent from my KFOT using Tapatalk
Sent from my KFOT using Tapatalk
ninjacentaur
Member
And I feel honored to have the great and mighty Stealth comment on my post.
Sent from my KFOT using Tapatalk
Sent from my KFOT using Tapatalk
ninjacentaur
Member
It's totally fine
the main reason I didn't post any photos is because I started this post prematurely and didn't have any progress to brag about. Now I only have a couple pieces left. 
the main reason I didn't post any photos is because I started this post prematurely and didn't have any progress to brag about. Now I only have a couple pieces left.
ninjacentaur
Member
Another one ...
Sent from my KFOT using Tapatalk
Sent from my KFOT using Tapatalk
ninjacentaur
Member
With the legs
well, what I have of the legs.
Sent from my KFOT using Tapatalk
well, what I have of the legs.Sent from my KFOT using Tapatalk
ninjacentaur
Member
This is an old pic from Halloween 
Sent from my KFOT using Tapatalk
Sent from my KFOT using Tapatalk
ninjacentaur
Member
The chest before I attached it to the back
Sent from my KFOT using Tapatalk
Sent from my KFOT using Tapatalk
ninjacentaur
Member
Now I'm working on the hands
Sent from my KFOT using Tapatalk
Sent from my KFOT using Tapatalk
ninjacentaur
Member
A little detail I added, it is a holder for my iPod nano. I put speakers. In my helmet and needed something to hold my iPod.
It's the angled thing in the middle, sorry for the bad lighting.
Sent from my KFOT using Tapatalk
It's the angled thing in the middle, sorry for the bad lighting.
Sent from my KFOT using Tapatalk
ninjacentaur
Member
finished cutting out the hand. Sent from my KFOT using Tapatalk
ninjacentaur
Member
Swag man
Sent from my KFOT using Tapatalk
Sent from my KFOT using Tapatalk
ninjacentaur
Member
Out of hot glue, going to go to the store tomorrow. Going to build the thigh. For Comic-Con I'm not going to try to finish the hand. (Its next Thursday) so I'm going to just wear some black and red gloves to improvise.
Sent from my KFOT using Tapatalk
Sent from my KFOT using Tapatalk
Mandarama826
New Member
Hello,
I have a few questions and would greatly appreciate it if someone could answer them for me.
I am attempting to build the iron man hand. I have downloaded all the pepakura files and I printed them all out on about 180 gram paper. I started putting together he lower palm knwoing that my paper was too thin but I just wanted to get the basic idea of where to fold what and how things go together.
SO here are my questions :
1. What kind of paper/ other material should I be using do that the lines come out clean and clear?
2. What glue should I be using to put all the pieces together?
3. Can the pepakura files be sent to 3d printing?
4. After I have the model built out of paper what can I put on top f it stifen it and make it hard so that I can bondo it and paint it?
Those are all my questions for the moment.
I would appreciate an answer as soon as possible since this is for a school assignment and I have to hand it in at then end of the semester.
THANK YOU!
I have a few questions and would greatly appreciate it if someone could answer them for me.
I am attempting to build the iron man hand. I have downloaded all the pepakura files and I printed them all out on about 180 gram paper. I started putting together he lower palm knwoing that my paper was too thin but I just wanted to get the basic idea of where to fold what and how things go together.
SO here are my questions :
1. What kind of paper/ other material should I be using do that the lines come out clean and clear?
2. What glue should I be using to put all the pieces together?
3. Can the pepakura files be sent to 3d printing?
4. After I have the model built out of paper what can I put on top f it stifen it and make it hard so that I can bondo it and paint it?
Those are all my questions for the moment.
I would appreciate an answer as soon as possible since this is for a school assignment and I have to hand it in at then end of the semester.
THANK YOU!
ninjacentaur
Member
I can help you a little. I use the foam method which is a little different. Thank you for asking!
1. I use 110lbs cardstock for printing out my pieces
2. I recommend hot glue, super glue works too but sets quickly, so if you mess up...
3. I don't know about 3D printing but I don't doubt someone else can answer. (Great question)
4. I believe the fiberglass resin method
Sent from my KFOT using Tapatalk
Similar threads
