Dangerous Resin, Have I Been Exposed?

[silverskyes402]

So I was drilling out and sanding a hole in the bottom of a resin hypospray kit today and instantly it started smelling of hardcore gasoline, witch i've never smelt before when sanding any kit, just wondering why and if it's dangerous, I dident smell a whole lot, but my clothes reek of it, just wondering if anyone had this experience before?

 

[glim999]

Yep. I've encountered a couple of castings that stunk like gasoline. Dunno why or if it's harmful though.

 

[Funky]

I wouldn't worry too much. Resin has a petroleum base and some times when it gets hot (like with drilling or cutting) you sometimes get that gasoline smell. I've had it happen a dozen times.

 

[TheSt.LouisKid]

If you feel off kilter in any remarkable way then I would suggest you get help. I wouldn't worry too much. If it were that dangerous I would be dead already judging by what you describe.

 

[KnightAsylum]

I would tell you the answer but likely you are already dead or mutated beyond the capacity to read so what would be the point:unsure












Actually never heard of such a thing, very strange - I am sure it will turn out just fine, seems like small exposure no matter what it was.:thumbsup

 

[silverskyes402]

Thanks for the replies you guys, I dont feel weird or anything, but I wasent wearing my respirator while sanding like a dumb ass so i was just wondering if I should go to the ER or not

 

[silverskyes402]

Ha Ha, love it! But my third and fourth eye's kinda hurt, is that a symptom?

I would tell you the answer but likely you are already dead or mutated beyond the capacity to read so what would be the point:unsure

 

[bobamatt]

Ha Ha, love it! But my third and fourth eye's kinda hurt, is that a symptom?

Nah, my fourth eye hurts all the time.

It's usually because of the lava that shoots out of it when I'm angry, sad,... and sometimes horny.

 

[BeastMaster]

I've been sanding and soldering/melting alot of metal from my sidkit. I wear a resperator mask, but it's just one of those white disposable ones. is this kind of mask ok for the job? or am I still potentially breathing in bits of metal?

also there arn't any apparent fumes when melting, though would I still need a proper filter mask anyway?

 

[Newbie Doobie]

Ha Ha, love it! But my third and fourth eye's kinda hurt, is that a symptom?

lollol Can't......stop.....:lol......laughing...Nee.d...Uu..h...AIR!!!!lol

 

[CessnaDriver]

If it were really bad, half the forum would probably be dead by now. :lol

 

[Newbie Doobie]

If it were really bad, half the forum would probably be dead by now. :lol

OK you guys!! I've got my second wind now,I can think somewhat straight!Always wear a respirator,and work outside,or away from pets,and people,or in a garage,or basement,if possible! If you experience headaches,dizzyness loss of hearing,the inability to speak,slurring - seek medical attention IMMEDIATELY!!!! I suggest that the escaping gases could cause blood damage,or other physical harm! I learned this when I joined the painters local union. Be vary careful when using solvent based materials. Especially if they give off any fumes! Breathing of silica can cause silicosis. Which is a condition that affect the lungs,and causes scarring which keep the lungs from processing oxygen,and if severe enough can cause slow suffocation! This is only an ocupational hazard usually. This keeps the oxygen in the lungs from being absorbed into the bloodstream efficiently to keep the blood from becoming poisoned. Most silicone,and latex products,including paint have this in them. Sanding residue is not an exception either!

 

[Zombie Killer]

OK you guys!! I've got my second wind now,I can think somewhat straight!Always wear a respirator,and work outside,or away from pets,and people,or in a garage,or basement,if possible! If you experience headaches,dizzyness loss of hearing,the inability to speak,slurring - seek medical attention IMMEDIATELY!!!! I suggest that the escaping gases could cause blood damage,or other physical harm! I learned this when I joined the painters local union. Be vary careful when using solvent based materials. Especially if they give off any fumes! Breathing of silica can cause silicosis. Which is a condition that affect the lungs,and causes scarring which keep the lungs from processing oxygen,and if severe enough can cause slow suffocation! This is only an ocupational hazard usually. This keeps the oxygen in the lungs from being absorbed into the bloodstream efficiently to keep the blood from becoming poisoned. Most silicone,and latex products,including paint have this in them. Sanding residue is not an exception either!

And there is no mask for silica. You must use a positive pressure air respirator. Basically a pump blowing air into a mask. You then where a hood over this and what air you don't breath is used to constantly keep air filling the hood and keeping out any debris. I use one for sandblasting cars. Even a military grade NBC gas mask will not work to remove silica. Don't ask how i know. Also the pos. pressure masks take some getting use to like using a scuba mask. Phobia ridden people usually don't like them. Don't play with silica the body has no way to get it out.

 

[Newbie Doobie]

And there is no mask for silica. You must use a positive pressure air respirator. Basically a pump blowing air into a mask. You then where a hood over this and what air you don't breath is used to constantly keep air filling the hood and keeping out any debris. I use one for sandblasting cars. Even a military grade NBC gas mask will not work to remove silica. Don't ask how i know. Also the pos. pressure masks take some getting use to like using a scuba mask. Phobia ridden people usually don't like them. Don't play with silica the body has no way to get it out.

That's what a respirator is! Mine is designed to keep particulates,and odors out! Mine is niosh,msa approved! These are specifically designed for industrial use without a separate air tank! These have particle filters to keep out air borne contaminates,and charcoal filters to keep out odors. These are specially designed with noeprene flaps to keep out these contaminates as well. This is made by 3M. These are used by industrial painters. Your talking about a helmet that goes over you entire head. These are only used for sandblasting! These don't keep out odors! These are also only for use with particulates of this kind -not for painting!