Y-Wing Parts Map for the "Green Leader" Project - open source

Re: Y-Wing Parts Map for the "Green Leader" Project

swgeek said:
It looks more like a fw 190 landing gear but the scissor is wrong.
Click to expand...

The 190 has a much longer strut compared to this one.

190 Fw190D9WheelWellsDone003SHF.jpg

P47p47fatcatlg_2.jpg
 
Last edited:
Re: Y-Wing Parts Map for the "Green Leader" Project

Thanks Dave! I'll edit that. I figured it had to be one piece, the Brummbar was close. Lol

This is coming from my phone, expect errors.
 
Re: Y-Wing Parts Map for the "Green Leader" Project

MonsieurTox said:
Yeah it is on the Nice-N /eFX pattern however it's not right, I guess the original part is a 1/72 landing gear with the compass cut off. Im still looking for the correct kit
Click to expand...

Good tip! :thumbsup
 
Re: Y-Wing Parts Map for the "Green Leader" Project

Post 79 says that #10 is from the Otaki 1/48 P51D Mustang. I can't find a scan to confirm but I'm sure it's right :)

Edit: And I believe #13 is a trimmed part A37 from the Nichimo Tiger II kit.
 
Re: Y-Wing Parts Map for the "Green Leader" Project

Here's a quick and dirty photo of the Otaki P-51D sprue. (I haven't taken them out of the bag yet!)

#10 looks like the landing gear oleo strut with some trimming.

Will link a full scan of the sprues to the spreadsheet over the weekend.
IMG_6119.JPG
 
Re: Y-Wing Parts Map for the "Green Leader" Project

Nice find! I've been looking at fighter aircraft landing gear most of the day.
 
Re: Y-Wing Parts Map for the "Green Leader" Project

swgeek said:
Nice find! I've been looking at fighter aircraft landing gear most of the day.
Click to expand...
Thanks! I've been looking off and on for a few years now. Very satisfying to finally come across it.

This is coming from my phone, expect errors.
 
Re: Y-Wing Parts Map for the "Green Leader" Project

You're correct. I was drinking last night. Lol.

This is coming from my phone, expect errors.
 
Re: Y-Wing Parts Map for the "Green Leader" Project

MonsieurTox said:
Found the sprue ! It was not where it should have been !
That's the part, awesome Don, Thanks !![/QUOTE

Can any one tell me what sprure these parts are on.I only have a partial kit & having trouble finding the parts.

Dave
Click to expand...
 
Re: Y-Wing Parts Map for the "Green Leader" Project

Is the Tamiya JPS 1/12 used on the Red Jammer? I see it uses a large part on the top of the Gold Leader, but wasn't sure about the possibility of it using a part on Red Jammer.

Also, is there any way to know exactly which Hasegawa 1/72 truck was used on the Y? I have the GMC Gas Tank Truck and the GMC Dump Truck as well. They both share the A sprue with the necessary piece so I wasn't sure. Unless I'm missing the identifying factor from another important piece from a different sprue that is.
 
This thread is more than 5 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.

Similar threads

KitSmasher
Need Parts Map for Escape Pod
Replies
3
Views
905
bwayne64
bwayne64
dtssyst
Y-WING 'Gold Leader' Studio Scale Build by dtssyst
6 7 8
Replies
150
Views
16,742
dtssyst
dtssyst
moffeaton
New parts patterned for a Hero X-Wing build
2 3 4
Replies
69
Views
9,009
camerafx24
camerafx24
Media Man
Tie Bomber Kit Parts Breakdown?
Replies
8
Views
577
Media Man
Media Man
bwayne64
More mystery parts, ; )
Replies
6
Views
991
bwayne64
bwayne64
Back
Top