TheRocketeer
Master Member
Re: Kingsman signet ring in Polished brass
Bump for the KIngsman
Bump for the KIngsman
-
Welcome to the Project Runs Forum!
This forum is intended for interest gauging and active runs. Due to the transient nature of this forum, please keep all research and ongoing discussion in one of our main forums so your information is not lost.
Only Premium Members can start a new run.
Done / Completed Kingsman signet ring
- Thread starter TheRocketeer
- Start date
katmurz
Active Member
Re: Kingsman signet ring in Polished brass
Back! My pinkie is a 4 and a 4.5...so question is if you still think it would scale down to that size well without loosing detail (going off the example being a 7, not sure if the signet would end up looking huge on a small finger basically)? If not my other fingers are all 5 or 5.5 so not much larger either lol.
Back! My pinkie is a 4 and a 4.5...so question is if you still think it would scale down to that size well without loosing detail (going off the example being a 7, not sure if the signet would end up looking huge on a small finger basically)? If not my other fingers are all 5 or 5.5 so not much larger either lol.
Bimmer
Sr Member
Re: Kingsman signet ring in Polished brass
The face will stay roughly the same size, while the band diameter changes more so it won't warp or be too small
The face will stay roughly the same size, while the band diameter changes more so it won't warp or be too small
Bimmer
Sr Member
Re: Kingsman signet ring in Polished brass
We could do silver or white gold plated! I've actually been wanting to do one in silver. Do you know your size?
bikemancs
Well-Known Member
Re: Kingsman signet ring in Polished brass
I don't, but I will be out and about today and will try to get it sized. I imagine I will be close to a 7, my ring finger on that hand is a 10 or 11.
I don't, but I will be out and about today and will try to get it sized. I imagine I will be close to a 7, my ring finger on that hand is a 10 or 11.
katmurz
Active Member
Re: Kingsman signet ring in Polished brass
Sorry for the delay, my real life is a bit hectic at the moment. I was advised for a smaller width band like this I should go size 3 for my pinkie, I realise that might be to small to fit the inscription but that is fine if I can't fit; not the first time I've had that issue lol If size 3 is too small, I can go 4 or 4.5 for my other fingers.
I'm also in Canada so let me know what info to shoot you in regards to my address for shipping cost; and then I can send you full payment for the ring and shipping asap. Thank you so much, sorry again in being slow.
Sorry for the delay, my real life is a bit hectic at the moment. I was advised for a smaller width band like this I should go size 3 for my pinkie, I realise that might be to small to fit the inscription but that is fine if I can't fit; not the first time I've had that issue lol If size 3 is too small, I can go 4 or 4.5 for my other fingers.
I'm also in Canada so let me know what info to shoot you in regards to my address for shipping cost; and then I can send you full payment for the ring and shipping asap. Thank you so much, sorry again in being slow.
TheRocketeer
Master Member
Re: Kingsman signet ring in Polished brass
OK we will figure out how small we an go with the rings. And they are being cast in the US so sent from there. I will find out about shipping and sizes and PM you
OK we will figure out how small we an go with the rings. And they are being cast in the US so sent from there. I will find out about shipping and sizes and PM you
JKKS
Sr Member
Re: Kingsman signet ring in Polished brass
Damn, I completely forgot about this.
I will take a brass ring in size 6 (my pinkie has a 52mm circumference so I think that's the size I need).
I will try to coat the inside of mine with clear nail polish as well. And if it doesn't do the trick it'll make a killer display piece anyways.
Could you please pm me with payment details ?
I'm very interested in the cufflinks as well if you guys think about tackling this project later.
Damn, I completely forgot about this.
I will take a brass ring in size 6 (my pinkie has a 52mm circumference so I think that's the size I need).
I will try to coat the inside of mine with clear nail polish as well. And if it doesn't do the trick it'll make a killer display piece anyways.
Could you please pm me with payment details ?
I'm very interested in the cufflinks as well if you guys think about tackling this project later.
Bimmer
Sr Member
Re: Kingsman signet ring in Polished brass
I can do 7 or 7.5 if you'd like. or even 7.25. It wouldn't be hard to have it sized up a .25 or .5 if need be after the fact. Let us know what you'd like to do
I can do 7 or 7.5 if you'd like. or even 7.25. It wouldn't be hard to have it sized up a .25 or .5 if need be after the fact. Let us know what you'd like to do
Re: Kingsman signet ring in Polished brass
Put me down for two sized 6.5
Put me down for two sized 6.5
joshspiderman23
Sr Member
Re: Kingsman signet ring in Polished brass
payment sent, i was way off on my initial ring size turned out to be a 5.5 lol, excited to get it
payment sent, i was way off on my initial ring size turned out to be a 5.5 lol, excited to get it
Bimmer
Sr Member
Re: Kingsman signet ring in Polished brass
Not really, these can be done just about any time but i prefer to do bulk ordering if possible. we''ll be ordering tomorrow or sunday. If you can't make it before then, it isn't the end of the world. Just PM me with your ring size when you figure it out
Not really, these can be done just about any time but i prefer to do bulk ordering if possible. we''ll be ordering tomorrow or sunday. If you can't make it before then, it isn't the end of the world. Just PM me with your ring size when you figure it out
Similar threads
