How do you get your Spidey eyes on?

cha0tic

Active Member
Well hey everyone, Out of curiosity how do you all get your eyes on? How do you line them up and get them perfectly.
I always seem to have a problem with it, even using crazydogs faceshell. Might just be im not that bright or something lol.
Let everyone know how you do it!
Sure this will help out bunch other people beside myself.
 
In order to get the correct position and spacing, you would need 4 things:

-Mannequin's head
-FaceShell
-Super Glue
-Lots of patience.

With my recent Symbiote and Scarlet Spider suit I used a new mannequin's head I got from Party City. Very cheap, foam, $5.

You slip your faceshell onto the mannequin head and position the frames of the mask onto the eyes of the head.

Then you take your frames and position them over your faceshell. This is a good way to determine how it matches with your face shell in terms of distance in between. Notice how the eyes of my mask aren't too close. They are about an inch apart from each other, starting at the front edges. To position the top edge of the frames, you want to make sure they are aligned onto a line and spaced between a certain number of web blocks on your fabric. Normally they should be spaced about 4-6 blocks away from each other.



View attachment 316292

If you see the bottom picture, my mask is pulled down and tightened around my head and shell. The shell I used was a Wal-Mart Ultimate Spidey mask. The area where the eyes go on the fabric, sink into the mask and it helps me determine position as well. I cut a small hole within the center of those areas. Then I place, not glue the frames over the frames of the face shell and tape them to figure out if they are properly aligned or spaced too far apart or too close. Once you get the proper adjustments, you tape the frames against the fabric at the sides, not the edges or corners. You want to secure the corners first with glue to make sure they stay at their anchor points of placement. Once the glue dries and the frames are secure, then go about gluing the rest of the frames.

View attachment 316293

and Voila!


DSC_8569_zpsa00e0eaf.jpg10245402_10203644314091886_1048092304967679486_n.jpg

- - - Updated - - -

In order to get the correct position and spacing, you would need 4 things:

-Mannequin's head
-FaceShell
-Super Glue
-Lots of patience.

With my recent Symbiote and Scarlet Spider suit I used a new mannequin's head I got from Party City. Very cheap, foam, $5.

You slip your faceshell onto the mannequin head and position the frames of the mask onto the eyes of the head.

Then you take your frames and position them over your faceshell. This is a good way to determine how it matches with your face shell in terms of distance in between. Notice how the eyes of my mask aren't too close. They are about an inch apart from each other, starting at the front edges. To position the top edge of the frames, you want to make sure they are aligned onto a line and spaced between a certain number of web blocks on your fabric. Normally they should be spaced about 4-6 blocks away from each other.



View attachment 316292

If you see the bottom picture, my mask is pulled down and tightened around my head and shell. The shell I used was a Wal-Mart Ultimate Spidey mask. The area where the eyes go on the fabric, sink into the mask and it helps me determine position as well. I cut a small hole within the center of those areas. Then I place, not glue the frames over the frames of the face shell and tape them to figure out if they are properly aligned or spaced too far apart or too close. Once you get the proper adjustments, you tape the frames against the fabric at the sides, not the edges or corners. You want to secure the corners first with glue to make sure they stay at their anchor points of placement. Once the glue dries and the frames are secure, then go about gluing the rest of the frames.

View attachment 316293

and Voila!


1656354_1435849129988864_1314472742_n.jpg10245402_10203644314091886_1048092304967679486_n.jpg
 
Its funny I had all of that, and managed to mess it up.
Might be because Im always trying to align it where my eyes would go and holes I make. Next suit I'm gonna slip the shell on the head put the mask on and just put glue them on and cut the holes from inside the mask.
Thanks alot man!

And great job on your suit :D
 
Take a look at my thread if you haven't already - I used a garbage bag laid over my face to get the positioning of my eyes correctly, then I laid the garbage bag "template" over the face shell to transpose the position.

http://www.therpf.com/f78/complete-...mbiote-diy-magnetic-face-shell-lenses-209315/

Not sure if that helps or not!

Ah yes, I ;ve seen it before. I like the approach you took :D

lol i had the same question
Hopefully this thread directs you to the answer :)
 
Back
Top