Help: A-Wing Aft Cockpit Bulkhead ID...

[imaginager]

Anyone have any ideas on any of these (except for the Vosper, of course).

 

[Guy Cowen]

Fingers crossed Allan someone can turn these up, I have only lightly glued mine in place in the hope they turn up one day

 

[tk1608]

This is prolly obvious and already ID'd, so forgive me 'cos I'm not an A-Wing expert, but I can see an F1 engine block on there laying flat. Also the long thin rectangle part stood up at the far rear...could it be a narrow radiator from an F1 ? Or could it be one of the churchill parts that are on the falcon radar dish ? I don't have that kit so I can't check..


Phil

 

[ralphee]

Part at the bottom/rear looks to be Ford DFV possibly, i CAN see a row of four Manifold flanges Allan.

lee

 

[ralphee]

Or, possibly the four white Manifold flanges from the 312T.

lee

 

[qcfoundry]

this is a wild stab..
the vertical radiator-like piece in the back..
could it be the (think its the alligator) bridge tank...from roco?

not even sure of scale...just windmilling

 

[imaginager]

Thanks, guys. TBH, I was getting an F1 vibe as I was manipulating that image yesterday. Even the parts on the vertical surface. Time to pull down all the F1 at 1/12 and 1/20... Q, yeah, my second feeling was possible ROCO, but a small radiator seems more likely. Was any ROCO used on ROTJ confirmed?
​

 

[tk1608]

Manifold flanges !!, I shudda put that instead of engine block,.. Lee knows all that F1 techie terminology..:lol

I should've posted a pic earlier to show what I was on about..

The white parts on the left are only casts because I don't have the full kits, but the top one with yellow arrow, I think is from the 1/35th churchill tank, as seen on the falcon radar dish, and the engine block manifold thingy, blue arrow, is from a 1/12th F1. The right hand parts are, Black arrow, a small radiator from, I think it's a 1/12th ferrari 312, and the white arrow is the same engine part as on the left but at 1/20th scale, from the tyrrell 6 wheeler,..

I'm not sure the size of the area these need to fit into, but one of the engine bits must fit..

I rushed this pic a bit, so if you need a better one with all the parts closer to the ruler let me know..

Cheers

Phil

 

[ralphee]

I think, Phil may have bagged this, looks too close to call buddy, id agree now its a DFV part anyhoo.

lee

 

[imaginager]

Looks like there's something else just aft of the mani, though... And, possibly 3 other something elses; double barrel centered and 2 flanking parts...

Mani is definitely 1/12

 

[imaginager]

Here's the double barrel deal:

 

[qcfoundry]

again...don't know the name, but feel like its the little "arm/pistons" that are on the stern "lip" over the back burner of the falcon. they run in pairs, i believe.
(edit-shoulda read allan's pic. sorry)

 

[eagle1]

The half-roundy shaped part with the ribs to the far right of the pic looks to me to be a ships launch hull, maybe Airfix or Revell?.
Kind of reminds me of the ones I built off Tamiya 1/350th ships but i don't think these were issued at the time 'Jedi' models were being built!.
Stu

 

[qcfoundry]

The half-roundy shaped part with the ribs to the far right of the pic looks to me to be a ships launch hull, maybe Airfix or Revell?.
Kind of reminds me of the ones I built off Tamiya 1/350th ships but i don't think these were issued at the time 'Jedi' models were being built!.
Stu

thats the vosper piece allan first mentioned

 

[tk1608]

This blue arrow thingy reminds me of an inspection lamp with a cage around it, could it be a plastruct wall light of some sort do you think ?

Phil

 

[jcuri1]

Both pieces are from the Tamiya 1/72 vosper in this last pic..

This blue arrow thingy reminds me of an inspection lamp with a cage around it, could it be a plastruct wall light of some sort do you think ?

Phil

 

[ralphee]

Yes John they are Vosper, the first part on the right i found an age ago though :lol

lee