Iron Man Mark 50 Speed Build (A LOT OF PICS)

jrdorag

New Member
Hey Guys, Everything good?

Finally i had sometime to post here, and i want to share with you my IronMan's Mark50 work, i did it in only 2 weeks for the premiere (25/04 here on Brazil),

HERE WE GO!!!

I really like to do my own 3D models for my armors, so i have sure it will come out just like i want, when i started, only have some images of the trailers and some arts, so i had to figure out how model it, i do some draws and sketches to it

received_1472441812882875.jpegreceived_1472441729549550.jpegreceived_1472441799549543.jpeg
*didn't find the one of the legs... haha


Then i modeled quick as possible and get to one satisfying result

untitled.23.jpguntitled.25.jpgMark50.43.jpgMark50.44.jpg

AND NOW IS THE PHYSICAL BUILD

when the model was ready, i finished the helmet to 3D print and the armor for foam, started doing some tests of curvature and seamlines and printing the helmet

P_20180330_200210.jpgP_20180402_000528_BF.jpgP_20180402_000533_BF.jpg

After that, started the chest piece, most iron man armors has the chest and abs in separated pieces, but in this one, i decided to build the entire torso in one piece, that causes a little less mobility, but i think is visually better

P_20180412_120251.jpgP_20180409_221535_BF.jpgP_20180412_002621_BF.jpg

Then it's just standard foam build until everything is ready for sealing and painting.

P_20180415_121745.jpgP_20180414_164414.jpgP_20180419_114430_BF.jpg


Sealing and painting... that's was really hard, my products didn't arrive because the post service here is horrible, then i had to figure out another way to do it, i decided to do some coat of water based resin, so it don't will crack the surface after painting, and will work "for now", i used polyurethane Metallic Red from Mercedes, i normally use as painting process Sealing > Black > Silver > Red, but i didn't had the silver paint, then the red looks a little too dark

P_20180421_143455.jpgP_20180421_163622.jpgP_20180421_170025_BF.jpgP_20180422_194913.jpg

After Painting everything and print the helmet and gloves, doing alot of sanding.. bondo.. sanding.. sanding.. more sanding... primer and was ready for paint

P_20180420_123737.jpgreceived_1512155455578177.jpegreceived_1512155735578149.jpeg



To be continued....
 

Attachments

  • P_20180422_205210.jpg
    P_20180422_205210.jpg
    2.1 MB · Views: 638
Part II -

Now... it's time to the polyurethane clearcoat

P_20180423_170014.jpgP_20180423_170041.jpgP_20180423_170058.jpg

And then, add the gold parts, silver details and a quick fitting test

P_20180424_180338.jpgP_20180424_212749.jpgP_20180424_213502_BF.jpg

Well, with only 3 days left to the premiere i had to run a lot with it to finish in time, so i didn't take a lot more pictures of the process of the legs, only when it was finished, but it came out in the same way that the rest of the armor

P_20180425_165112_BF.jpgP_20180425_165130_BF.jpg


So.. last fitting test (without any of the joints, straps, zippers, and velcro yet) came out like this:

received_1810650212319889.jpeg

The thigh pieces did'nt attach very well on the codpiece, but after the fitting test i put some foam inside with a little buckle to make sure it's will be on the place.


To be continued..
 
Part III - ARMOR DONE!!

So.. after running a lot, i finished the armor a few hours before the premiere, for the time i had to produce, i think this came out good enough, but after see the movie, i notice a lot of things that i can improve on this armor (basically build a new one hahaha), but... that's it, hope you like it, and enjoy!!

received_1522598981200491.jpegIMG-20180507-WA0017.jpgIMG-20180507-WA0021.jpgreceived_1768465736547294.jpegreceived_1768465779880623.jpeg
(in the theater was a lot of persons with cosplays too, unfortunately i didn't find most part of the pictures, but i find somes.. haha)

*Few minutes before the movie, i take off the armor to watch the movie more comfortable hahaha

P_20180425_234135_BF.jpg


-= The End =-
 
Thank you guys, i'm planning to do a version 2.0, with better proportions, some Latex pieces (like the neck and handplate) and to be a little more "functional", to have a better movement, and,of course, the right color haha
 
This thread is more than 5 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top