Build thread: Jinx' rocket launcher "Fishbones" from League of Legends

Volpin

Sr Member
RPF PREMIUM MEMBER
I'll admit, I've never played League of Legends. The design of this thing is so cool looking though, I had to make it. Luckily my desire for a new project coincided with a potential client email, and I'm getting to build one!

Screenshot 2013-11-15 11.46.54.png

Fishbones is a shark shaped rocket launcher. It's pretty damn big, and since this piece will be used as both a costume and display prop, I have to try to keep things lightweight, durable, but also replica quality. Gotta love a challenge. The gun will also be able to open and close the shark jaws with a pull handle and have illuminated eyes and barrel.

I've got a ton of progress done on this already but I'll break it up over a few posts so there isn't some monster brick of text in the first page. This post will just cover the sharketlauncer's jaws. Here's where I'm currently at as of about a week ago:

13884379923_50d8a77a2c_c.jpg


After mocking up some 2D blueprints, I set about sculpting the head. This is urethane tooling foam sculpted over plastic spines to mark the profiles, followed with a bit of bondo.

12288449973_9a2e5e3885_c.jpg

12288446643_d80eb25025_c.jpg

12288843066_bc70593a84_c.jpg


Same process for the lower jaw

12288700474_f29046a833_c.jpg

12288426883_2299e513f2_c.jpg

12288420553_c05fa9a584_c.jpg


Details were added with apoxie sculpt and layered sintra. Keep in mind these are just mold masters, so I'm not really concerned about weight at the moment.

12369824335_c5a090652c_c.jpg

12370276214_21ce972e38_c.jpg


Here's the head, ready for molding:

12504188335_2be2d12568_c.jpg


Molds were 2-part silicone brush on with Smooth-On's Rebound 25. The castings were done in layered epoxy with glass fiber backing to keep things lightweight. Here's the print coat, done in EpoxaCoat Red for the gel layer:

13642553874_c5f461c15b_c.jpg


Cavities were filled with Free Form Air before layering with glass cloth and EpoxaMite epoxy. This makes sure there aren't any air bubbles or weaker areas from where the glass fiber can't curve around sharp corners.

13642234363_cd45a4ca76_c.jpg

13642642944_d8cf3da47c_c.jpg


The resulting casts are very lightweight and strong.

13642319293_d7c5d1f930_c.jpg


Also, happily, the jaws fit into one another perfectly! I was a little nervous sculpting them separately but it all worked out in the end. Whew.

13642325043_18c0884c16_c.jpg


More to come soon, thanks for reading!
 
Woof, I need to remember to update more often.

So here's how I went about putting the body of the gun together. I need this to be as light as possible, and that'll be tough with a 40" long rocket launcher. The barrel that runs down the center is a myriad of intersecting pipe dimensions. This could be approximated with PVC pipe but it would result in a very heavy component. I decided to vac form mine.

This started out with a giant chunk or urethane tooling foam, chucked up on my wood lathe.

13320095463_346f4711bd_b.jpg


Urethane foam tools like butter, and I had this shape knocked out in a few minutes. If only everything could go so quick! I did a couple more pieces for the rear most components of the barrel too.

13319933575_e689cb59d8_b.jpg

13437625623_15b932ff4c_b.jpg


These were all pulled in .060" styrene sheet on my vac former.

13319931205_fa39fbb1e0_b.jpg


Obviously, this leaves a bit of a seam. I pulled a third copy and used it as an interior lip to glue the halves together, then blended the seam with some bondo.

13437846014_5fbe4b6d21_c.jpg


The resulting part is light, if a bit fragile.

13437849804_66fb4b88f6_c.jpg


I made an interior "sleeve" out of thin walled PVC to sit inside this vac formed part. All of the parts of the gun will eventually be anchored to this central spine so the thinner styrene doesn't take the brunt of any force. To save more weight, I cored out a ton of holes. This saves over a half pound with no noticeable reduction in strength.

13489299483_e6bc624f3d_c.jpg


The front barrel is a piece of 6" thin wall PVC with a few sintra spacers at the rear to align the rear barrel. The tapered muzzle is a piece of urethane resin turned on the lathe and secured to this front barrel.

13437485555_24eba7d982_c.jpg

13489539194_6ce9e11570_c.jpg


This is all back log stuff to get this thread up to speed. I've made a ton more progress and should be going to paint in the next couple of weeks! More updates to come soon.

13940582840_ffa9b4561c_b.jpg
 
I've been following every update on this marvelous thing via Flickr and Facebook. Can't wait to see it done!

Thanks! It's kind of an obscure one, but a fun project.

Onto the armor plates! The bulk of these are made from layered PVC sheet (sintra) because it's very easy to shape into simple curves and it carves easily. I made a bunch of mockups on several of the parts before going all out.

13729414105_491a7ba39b_b.jpg


The beveled edges were added in sections to a base of bent PVC. I used my vac former oven to heat the whole sheet, then curled it around various diameter pipes for each plate until I got the radius I wanted.

13748083054_c9130b57cd_b.jpg


To get the whole perimeter beveled, I started off with my grinder and a really rough bit to remove a lot of material very quickly. It's very easy to zip off way too much since the sintra offers very little resistance, so this is actually more of a delicate operation than it might seem.

14127205105_30e9efae30_b.jpg


This is followed by a pass with my dremel, then various grits of sandpaper and blocks until its niiiice and smooth.

13940585908_377e3d6eab_b.jpg


That's the general process for pretty much all 4 armor plates. In the end, they're nice and lightweight but still quite rigid!

13884704944_babeedc701_b.jpg
 
Where do you get this type of tooling foam? Can it be bought in stores?

I've been looking for something similar to this to make Fallout props for a while now.
 

Would you mind showing the type of bit you used for this part? I'm guessing it's a metal cylinder rasp...

It looks like with enough finesse (and a light sanding), you could easily give PVC pipe a wood grain effect. Might be a godsend for people who make staff's and wooden sheild's out of plastic.

Awesome job as always sir!
 
Where do you get this type of tooling foam? Can it be bought in stores?

I have a friend who gives me smaller scraps from time to time, they use mostly very large sheets for concept cars so anything under 10" cube is more or less trash. They drop me a big ol' box and I make my parts out of that. Several suppliers do sell it though, from eBay to people like The Engineer Guy here in Atlanta. Not sure if I've ever seen it in retail though.

Would you mind showing the type of bit you used for this part? I'm guessing it's a metal cylinder rasp...

Sounds right. It looks like this:

7987145787_bc96385693_c.jpg


So, more updates! I need to get caught up since this project is nearing completion soon...

I've designed the jaws so they can open and close with a small trigger next to the handle. The first step was to create some anchorpoints inside the jaw for hinge pins. These are T-nuts epoxied in place. The post makes sure they're mounted in line with one another.

13642641814_2812333a17_c.jpg


I eventually added a second pin to act as the pivot arm, since articulating the assembly on these threaded rods meant they were constantly backing out of the T-nuts.

14141931166_4d1b64bfe4_c.jpg


This was the original set-up for the jaws:

13729377745_40c84a8f3c_c.jpg


But this proved to be problematic, so the pivot arms were added as well as a few return springs. Now the jaws clap closed with authority but pulling the trigger isn't too difficult or uncomfortable.

13978445927_9c45875ba6_c.jpg


Here's a shot from the backside looking forward, where you can see the trigger and articulating cable routed through an aluminum plate.

14165176404_006bfd86dd_c.jpg


The result of these efforts can be seen here!

More posting catching up needs to happen, I've already started on paint. Hope to be done before the end of the month. WOOOOOOOO

14064343229_e536f16315_c.jpg
 
This thread is more than 9 years old.

Your message may be considered spam for the following reasons:

  1. This thread hasn't been active in some time. A new post in this thread might not contribute constructively to this discussion after so long.
If you wish to reply despite these issues, check the box below before replying.
Be aware that malicious compliance may result in more severe penalties.
Back
Top