Does anyone have some really good pics of the Rebel Endor blaster rifle? In the only ones I have found, you can't see the detail of the rifle very well.
Rebel Endor Blaste rifle - good pics?
- Thread starter Sluis Van Shipyards
- Start date
Jedi Loreen
Well-Known Member
It might be stating the obvious, but have you seen these sites? You don't mention where the pics you've seen are from.
http://www.partsofsw.com/EndorBlas.htm
http://www.studiocreations.com/howto/endorrebelsoldier/index.html
http://www.partsofsw.com/EndorBlas.htm
http://www.studiocreations.com/howto/endorrebelsoldier/index.html
Last edited by a moderator:
Yeah I've seen both of them, thanks though!
I forget now... :lol I just remembered I still needed them last night.
I think mainly around the delta ring (where the M-16 barrel would attach). I've got a couple tiny pictures that look like the t-shaped stock version has different detail around there. Also I wanted to figure out how the little pouches attach; whether they are like saddle bags or if they were stuck on seperately to each side of the tube.
I'm going to attempt to make it with as many metal parts as possible, so we'll see how it goes.
Wow, this thread could've been started by me. I've also been wondering if higher res versions of those pics were available.. oh well!
I have an airsoft M4 that I'm going to use, and retain function. Our airsoft group is a wacky bunch, and our game nearest Halloween is going to be played in the costumes of our choice! My Endor trooper won't be ready by then but there's always next time.
I have an airsoft M4 that I'm going to use, and retain function. Our airsoft group is a wacky bunch, and our game nearest Halloween is going to be played in the costumes of our choice! My Endor trooper won't be ready by then but there's always next time.
If I remember right in an older thread, someone thought it may have not been an AR15/M16 flash hider, but another assault rifle.
Anyone have any idea about the flash hider? The ones I've seen don't have the groove that runs through the little ovals.
That's what I'm thinking too. I may just scratch the flash hider together out of metal tubing.
Does anyone know where to get an airsoft Delta ring for the M16 like this one?
The only ones I've seen online (and mistakenly bought...) are for later model M16s. The version on the Endor blaster seems to be like this without a taper towards the muzzle.
The only ones I've seen online (and mistakenly bought...) are for later model M16s. The version on the Endor blaster seems to be like this without a taper towards the muzzle.
The non tapered delta rings are hard to find afaik.
I bought a lower receiver parts kit plus a few additional parts from a member here and I know it took him quite a time to find a dealer that carries them AND has one in stock.
Have got all -rel- parts now to upgrade my Endor rifle, which I built with Matts awesome resin receiver combo back the days
Markus
I bought a lower receiver parts kit plus a few additional parts from a member here and I know it took him quite a time to find a dealer that carries them AND has one in stock.
Have got all -rel- parts now to upgrade my Endor rifle, which I built with Matts awesome resin receiver combo back the days
Markus
Does anyone know where to get an airsoft Delta ring for the M16 like this one?
The only ones I've seen online (and mistakenly bought...) are for later model M16s. The version on the Endor blaster seems to be like this without a taper towards the muzzle.
Check out G&P...they seem to have a straight delta ring.
Markus
Yeah I was going to try their main site after I'm done here. I checked Redwolf and a couple other places with no luck. - I checked G&P's site and you can get a total front with the correct delta ring, but they only seem to sell the tapered one. That front kit is $110...
Does anyone know if both styles of the Endor blaster had magazines? The Complete Visual Dictionary (M16 with MG34-looking stock version) shows it with a magazine, but the other version seems to have a plate or something covering the magazine well.
Last edited:
Why not use a real M16 ring? Shouldn't the size be close enough?
Sherluk has "straight" delta rings for $10 (along with other parts)
http://www.sherluk.com/m16d.php
Sherluk has "straight" delta rings for $10 (along with other parts)
http://www.sherluk.com/m16d.php
Ok, I was asking because the following pic has a cut down mag in it: http://rogue74.nt3.npsis.com/endorblasternwvd.jpg
I was thinking about doing that too. I think the metal airsoft body I have it supposed to be the same size as a real upper/lower receiver. I'll check that site out, thanks!
