NECA berserker predator bio mask lighting sights

moonshadow1

New Member
To my brothers

Hi~ it's me again,just fall in love with LED light these days and decided to make a custom predator mask with lighting sights, I made 3 tiny holes with needle (my finger still hurts....), then insert
optical fibres into those holes and put a red LED behind the mask, now this is what I got so far~


I took off all NECA new predators' masks and found out that they look quite nice together


Hopefully I'll add LED to all of them soon~
 
Last edited by a moderator:

moonshadow1

New Member
How did you get the masks off?

Are those just masks, or is there still some of the Pred head attached?


How to get them off? use your strength brother

Yes those are only masks, I gonna install battery and switch inside the mask, once finished they can be put back onto heads~
 

sabres21768

New Member
How to get them off? use your strength brother ;)

Yes those are only masks, I gonna install battery and switch inside the mask, once finished they can be put back onto heads~

I tried once with a Falconer figure...didn't even come close to getting it off.

Now I feel weak.

 

Sorrow

New Member
Immersed the head in boiled H2o for about a minute or two to soften plastic and glue, thats the easiest way, then you can pull it off easily. Hope this helps.



Moonshadow will a watch battery work for the LED's? And where do you plan to put the switch if you'll put one? Sorry for the curiosity.
 

sabres21768

New Member
Immersed the head in boiled H2o for about a minute or two to soften plastic and glue, thats the easiest way, then you can pull it off easily. Hope this helps.



Moonshadow will a watch battery work for the LED's? And where do you plan to put the switch if you'll put one? Sorry for the curiosity.

Thanks, I'll give that a try.

And sorry about what happened in your other thread, I really didn't mean to come off as trying to give you a hard time.

My bad, and I hope there are no hard feelings.
 

Sorrow

New Member
Thanks, I'll give that a try.

And sorry about what happened in your other thread, I really didn't mean to come off as trying to give you a hard time.

My bad, and I hope there are no hard feelings.
No hard feelings here sabes, and if I offended you in anyway, I apologize too. Lets bury the hatchet.
 

moonshadow1

New Member
Thanks, I'll give that a try.

And sorry about what happened in your other thread, I really didn't mean to come off as trying to give you a hard time.

My bad, and I hope there are no hard feelings.

actually you can try to find or even make a gap between mask and head, insert a knife or a screwdriver,PRY! XD
 

moonshadow1

New Member
Immersed the head in boiled H2o for about a minute or two to soften plastic and glue, thats the easiest way, then you can pull it off easily. Hope this helps.



Moonshadow will a watch battery work for the LED's? And where do you plan to put the switch if you'll put one? Sorry for the curiosity.


3 button batteries will do, and I got some mini switches about 10mm in lenght, I will figure out a way to install them all inside the mask~
 

cityhunter96

New Member
thats really cool. thats the type of creativity customizing gets ya. you start with your figure and then as jimmy neutron would say BRAIN BLAST. i should add LEDs and boom a bad ass figure mask is born
 
This thread is more than 11 years old.

Your message may be considered spam for the following reasons:

  1. Your new thread title is very short, and likely is unhelpful.
  2. Your reply is very short and likely does not add anything to the thread.
  3. Your reply is very long and likely does not add anything to the thread.
  4. It is very likely that it does not need any further discussion and thus bumping it serves no purpose.
  5. Your message is mostly quotes or spoilers.
  6. Your reply has occurred very quickly after a previous reply and likely does not add anything to the thread.
  7. This thread is locked.
Top