What you get (flat-molded, large enough to mold -- not double-sided molds, and nothing from below that is too small to mold)
1/35 Tamiya Panzerspahwagen 8rad nurnies
1/72 Sherman nurnies (but not super-tiny-too-small-to-mold pieces)
1/25 Tamiya Centurion nurnies
1/24 Airfix Hurricane nurnies
1/24 Airfix P-51 nurnies
1/24 MPC AV-8A Harrier nurnies
1/24 Bandai Shiden nurnies
1/48 Bandai Piper/Cessna 150/Aero Subaru 200/Beech Bonanza Lycoming engine nurnies/cockpit nurnies
1/48 Bandai Nashorn (engine thruster nozzle) nurnies
1/72 Airfix Handley Page 0/400 Bomber nurnies (except piping nurnies that go on engine dressings -- too small to mold)
1/48 Otaki P-51 Mustang (body nurnie only, NOT landing gear nurnies -- too small to mold)
1/48 Fujimi Japanese Navy Type 99 Carrier Dive Bomber nurnies
1/72 Airfix F4-E Phantom II "toothpaste cap" engine nurnie for neck bottom next to Morgan oil pan nurnie
1/16 Morgan nurnies (plate piece X2, and neck bottom piece X1)
1/35 Tamiya No. 89541, M551 Sheridan Part # A42, cupola top plate nurnie
1/35 Nichimo Jagdtiger nurnies, backplate for Y-Wing in original size, does not fit (too large) DaveG's armature, but can be cut down to fit.
1/35 Tamiya Panzer Kampfwagen III Ausf. M/N nurnies, but NOT the gun barrel mount (double-sided mold) for nacelle-tie-downs, all other nurnies included, of which you need several
1/35 Italeri/Testors 155 mm Howitzer Gun M1-A2 nurnie, for upper fuselage cross section.
1/35 Tamiya 20 mm Flak 38 (Part #A70) nurnies
1/15 Bandai Hummel German 150mm Howitzer Self Propelled 4 SdKfz 165 nurnies -- all of them, and all you need
1/15 Bandai Tank 4 - rectangular piece nurnies
1/9 Kettenkrad nurnies, at least 2 track links, plus 2 bumps, and bottom hole-mount half-round piece, but NOT tow-hook pieces for nacelle-tie-down subassemblies (buy DaveG's Hong Kong produced set of 8 pieces, they are nearly flawless)
1/35 Tamiya Hanomag Sdkfz 2511 part numbers B13 and B14 (but NOT piston rods for rear ventral controls, buy DaveG's set instead, they are perfect)
1/35 Tamiya 25 Pdr nurnies, of which you'll need lots, for bulkhead and other areas
Bandai 1/48 Schwimmwagen Type K2 nurnies, for sidewall dressings on 8rad neck pieces
Airfix 1/76 Amphibious Buffalo neck ramp piece (but NOT the super-tiny unmoldable pieces)
Airfix 1/76 Scammell Tank Transporter Part #58 modified trailer chase piece for lower fuselage
Roco 1/87 HO Z-132 HO Model Miniatures Minitanks No. 132 Sperrhindernisse Antitank Obstacles nurnies (for rear-of-engine trapezoid nurnies -- n.b. THESE may NOT be authentic, per DaveG's measurements, and his trapezoids are more accurate and available on Shapeways. This ONLY matters if you want a super-accurate Y-Wing of EXACTLY 38cm width in which case you need to purchase separately (for $45) a Tee-Plate of exactly 34.0cm)
AMT 1/25 International Payhauler nurnies, for lower fuselage rears section
1/12 Tamiya Yardley M23 nurnies
1/72 Hasegawa GMC CCKW-353 Gasoline Truck for part #15, crankcase for upper fuselage nurnie
1/500 Nichimo Musashi Conning Tower nurnie, SUPER RARE and hard to find
1/200 Nichimo I-19 Submarine plate nurnies to hold spinner/hub from Hurricane, you get blanks AND 2 completed subassemblies
1/600 Airfix Mauretania skylight nurnies
1/130 Frog Shell Welder nurnie, one piece only, for droid socket area on upper fuselage
1/600 Monogram USS Saratoga nurnies, Part #40/80 landing lights that go on upper fuselage midsection
00 Airfix Harrow train nurnies, but NOT the 2 super-delicate Harrow nurnies needed for rear vectral fin dressing
2 Castings of anodized heat sinks from Aavid Thermalloy -- these don't mold super-perfectly/accurately, but are included in each set in whatever form they come out in. If you're adding lights (heat-generating) to your model, you'll probably want originals made of metal.
Various/sundry 1/700 Tamiya ship nurnies (too many to list separately)
Numerous one-off pieces from the various 1/48 Bandai tank kits that are confirmed donors
All the bulkhead nurnies, including angled plating to make the substructure.
Literally DOZENS of pieces from either a.) the models listed above or b.) models not listed above that are "interpretive" nurnies for alternate dressing of your Y-Wing, or for use on other model projects. Of all the pieces, probably 30% are interpretive/alternative pieces.
You get a whole bunch of pieces you won't need, extras, and stuff you can use on your Millennium Falcon build b/c there's a good deal of crossover in the confirmed donors.
You also get a variety of pieces that are, in fact, too small to mold, but are included on some of the molds, and with which you can either a.) throw them out b/c they're junk, b.) use them as a size/reference guide to scratchbuild your own out of Plastruct/Evergreen, c.) use them anyway and hope a thick layer of paint will cover all sins, or d.) bitch and moan to me about how these pieces didn't come out well.
Basically, you get all the pieces necessary for the average Star Wars fan to say, "Oh Wow, a Studio Scale 1/24 Y-Wing!" while only the Officially Sanctimonious Rivet-Counters will be able to say, "Hey, wait a minute, where's the piece from X?" (
n.b., on planet Earth, there are less than 10 Officially Sanctimonious Rivet Counters)
What you don't get:
1/93 Sealab nurnies (you get some, but not all of them -- future releases will include all of them -- i.e., once I get a complete/new Sealab and not the "already built" one I got on Ebay for $12 and hacked apart!)
1/24 Bandai Me-109 landing gear nurnies (double-sided mold, not made yet)
Nacelle Tie-Down nurnies -- I have an original mock-up, and may make a two-sided mold of it, but mine still won't hold a candle to the perfection of either DaveG's tie-downs or Tony's tie-downs on Shapeways.
Rear Vectral Shroud nurnies, control vanes, or anything on the rear vectral controls.
Engine Thruster inserts, nozzles, or fins (But you DO get engine interior nurnies, and you do get 2 Payhauler rim nurnies which hold the heatsinks perfectly.)
Various/sundry 1/700 Tamiya ship nurnies, many of which are too small to mold
1/600 Otaki Yamato nurnies (I can't find this ship anywhere, and I have friends in Japan, so if you find a casting, get it)
1/144 Airfix Saturn V nurnies -- you HAVE to buy 2 of these either way, so none of these nurnies are included
You don't get the Sat Can nurnies, b/c MasterPiece Models already does a 10-pack of those (
Y-Engine Greeblie Pack), and for a great price (but you do get the Hummel "ramp" nurnies and Heinkel He 177 landing strut nurnies that are used on the Sat Cans, just not in sets of 10, you only get a few of each).
SOME of the Tamiya 1/35 Panzerspahwagen 8rad nurnies, that are too small/thin/delicate to mold. But you do get two of the neck sidewall pieces, and others)