The Portugeek
Sr Member
Re: LOKI Helm
It sure is. This is an ongoing run. Send me a pm
It sure is. This is an ongoing run. Send me a pm
-
Welcome to the Project Runs Forum!
This forum is intended for interest gauging and active runs. Due to the transient nature of this forum, please keep all research and ongoing discussion in one of our main forums so your information is not lost.
Only Premium Members can start a new run.
Unlimited Run LOKI Helm THOR movie
- Thread starter The Portugeek
- Start date
The Portugeek
Sr Member
Re: LOKI Helm
It sure is. This is an ongoing run. Send me a pm
It sure is. This is an ongoing run. Send me a pm
Re: LOKI Helm
Just posting an update - the helmet has been remastered and there are no longer any seams on the main helmet. As well, the horns are way easier to attach. It's all under rubber right now but once we can get a cast pulled we will post some updated pictures.
Just posting an update - the helmet has been remastered and there are no longer any seams on the main helmet. As well, the horns are way easier to attach. It's all under rubber right now but once we can get a cast pulled we will post some updated pictures.
Stealthxware
Jr Member
Re: LOKI Helm
How tall is the entire helmet with horns on it? Also how do you attach the horns with the updated mold?
How tall is the entire helmet with horns on it? Also how do you attach the horns with the updated mold?
The Portugeek
Sr Member
Re: LOKI Helm
It stands at around 19" tall. Maybe TJack can confirm this.....
We weren't fans of how the casts came out of the original mold so some things have been changed in V2.0
One of those things being how the horns are attached. Tjack can you post a picture showing how they go together now?
It stands at around 19" tall. Maybe TJack can confirm this.....
We weren't fans of how the casts came out of the original mold so some things have been changed in V2.0
One of those things being how the horns are attached. Tjack can you post a picture showing how they go together now?
Last edited by a moderator:
Re: LOKI Helm
Yep I measure about 19" as well.
The old helmet had a few seam lines that we removed and it's now a glove mold so there are no seam lines on either the main helmet or the horns. Sorry for the poor iphone pics, I'll get some better ones up when I have the chance.
As well, the old helmet had the lower 4-5" of the horn attached to the helmet which required you to attach the remainder of the horn to it (which was a bit of a challenge). As part of the remaster, we removed that part from the helmet and made the horn 1 piece for easier assembly. The entire horn now sits over the "bump" you can see at the front of the helmet. The horns are foam filled with a resin cap.
To attach the horns you will need to drill a pilot hole in the "bump" then place the horn over the bump to drill the pilot hole into it as well. Then you can apply some epoxy or your adhesive of choice to the bump and inside of the horn then drive a screw from the inside of the helmet into the pilot hole in the horn to secure it in place. You will then need to use some filler to clean up the seam where the horn attaches to the top of the helmet. Hopefully that all makes sense?
We will include detailed instructions when purchased.
It stands at around 19" tall. Maybe @TJack can confirm this.....
We weren't fans of how the casts came out of the original mold so some things have been changed in V2.0
One of those things being how the horns are attached. Tjack can you post a picture showing how they go together now?
Yep I measure about 19" as well.
The old helmet had a few seam lines that we removed and it's now a glove mold so there are no seam lines on either the main helmet or the horns. Sorry for the poor iphone pics, I'll get some better ones up when I have the chance.
As well, the old helmet had the lower 4-5" of the horn attached to the helmet which required you to attach the remainder of the horn to it (which was a bit of a challenge). As part of the remaster, we removed that part from the helmet and made the horn 1 piece for easier assembly. The entire horn now sits over the "bump" you can see at the front of the helmet. The horns are foam filled with a resin cap.
To attach the horns you will need to drill a pilot hole in the "bump" then place the horn over the bump to drill the pilot hole into it as well. Then you can apply some epoxy or your adhesive of choice to the bump and inside of the horn then drive a screw from the inside of the helmet into the pilot hole in the horn to secure it in place. You will then need to use some filler to clean up the seam where the horn attaches to the top of the helmet. Hopefully that all makes sense?
We will include detailed instructions when purchased.
Last edited:
Stealthxware
Jr Member
Re: LOKI Helm
Awesome, seems a lot easier than the original. What size head will it fit?Yep I measure about 19" as well.
The old helmet had a few seam lines that we removed and it's now a glove mold so there are no seam lines. Sorry for the poor iphone pics, I'll get some better ones up when I have the chance.
View attachment 503440View attachment 503441View attachment 503442
As well, the old helmet had the lower 4-5" of the horn attached to the helmet which required you to attach the remainder of the horn to it (which was a bit of a challenge). As part of the remaster, we removed that part from the helmet and made the horn 1 piece for easier assembly. The entire horn now sits over the "bump" you can see at the front of the helmet. The horns are foam filled with a resin cap.
View attachment 503443
To attach the horns you will need to drill a pilot hole in the "bump" then place the horn over the bump to drill the pilot hole into it as well. Then you can apply some epoxy or your adhesive of choice to the bump and inside of the horn then drive a screw from the inside of the helmet into the pilot hole in the horn to secure it in place. You will then need to use some filler to clean up the seam where the horn attaches to the top of the helmet. Hopefully that all makes sense?
View attachment 503444View attachment 503445
We will include detailed instructions when purchased.
Re: LOKI Helm
Same as the original - you may be able to squeeze a 24" head in it but it will be snug. I can wear it and I'm 23.5 but there isn't much extra room. However, it is resin so with a little heat you can always adjust it for a better fit.
Same as the original - you may be able to squeeze a 24" head in it but it will be snug. I can wear it and I'm 23.5 but there isn't much extra room. However, it is resin so with a little heat you can always adjust it for a better fit.
The Portugeek
Sr Member
Re: LOKI Helm
Well said.
Well said.
Yep I measure about 19" as well.
The old helmet had a few seam lines that we removed and it's now a glove mold so there are no seam lines on either the main helmet or the horns. Sorry for the poor iphone pics, I'll get some better ones up when I have the chance.
View attachment 503440View attachment 503441View attachment 503442
As well, the old helmet had the lower 4-5" of the horn attached to the helmet which required you to attach the remainder of the horn to it (which was a bit of a challenge). As part of the remaster, we removed that part from the helmet and made the horn 1 piece for easier assembly. The entire horn now sits over the "bump" you can see at the front of the helmet. The horns are foam filled with a resin cap.
View attachment 503443
To attach the horns you will need to drill a pilot hole in the "bump" then place the horn over the bump to drill the pilot hole into it as well. Then you can apply some epoxy or your adhesive of choice to the bump and inside of the horn then drive a screw from the inside of the helmet into the pilot hole in the horn to secure it in place. You will then need to use some filler to clean up the seam where the horn attaches to the top of the helmet. Hopefully that all makes sense?
View attachment 503444View attachment 503445
We will include detailed instructions when purchased.
Re: LOKI Helm
Just to revive this here a bit, I've been in contact with Sunkistshark and I will be offering a premium studio-quality finishing service on these helmets for anyone interested.
I'll have a sample helmet to work on hopefully soon so you guys can see what one will look like after It leaves my shop.
Just to revive this here a bit, I've been in contact with Sunkistshark and I will be offering a premium studio-quality finishing service on these helmets for anyone interested.
I'll have a sample helmet to work on hopefully soon so you guys can see what one will look like after It leaves my shop.
quantumsissy
New Member
Re: LOKI Helm
Hi! Is there any available? I would like one to Singapore, 650402. How much does that cost? Cheers, Richard
Hi! Is there any available? I would like one to Singapore, 650402. How much does that cost? Cheers, Richard
Re: LOKI Helm
They will be after I get back from vacation Aug 10. Shipping to Singapore will vary depending on how soon you want it and if you want tracking/insurance. It can be anywhere from $30 to $150.
They will be after I get back from vacation Aug 10. Shipping to Singapore will vary depending on how soon you want it and if you want tracking/insurance. It can be anywhere from $30 to $150.
quantumsissy
New Member
Re: LOKI Helm
great! I want one, and I can only receive it mid October, so time wouldn't be an issue. Can I get a quote on this?
great! I want one, and I can only receive it mid October, so time wouldn't be an issue. Can I get a quote on this?
The Portugeek
Sr Member
Re: LOKI Helm
Has Tjack taken care of you already? I see he had given a rough price for shipping...
You talking about a finished one from General Frosty? If so he hasn't quoted the job yet until he gets his hands on one first. Which will be soon.
Has Tjack taken care of you already? I see he had given a rough price for shipping...
great! I want one, and I can only receive it mid October, so time wouldn't be an issue. Can I get a quote on this?
You talking about a finished one from General Frosty? If so he hasn't quoted the job yet until he gets his hands on one first. Which will be soon.
quantumsissy
New Member
Re: LOKI Helm
Yes, I have discussed with him. I understand that he will be back on the 10th so I'll be in contact with him again then many thanks!
Yes, I have discussed with him. I understand that he will be back on the 10th so I'll be in contact with him again then
many thanks!
The Portugeek
Sr Member
Last edited by a moderator:
The Portugeek
Sr Member
Re: LOKI Helm
To the top
To the top
Similar threads
