Kylo Ren Junk Saber Build

[Hanslow]

Funny you should mention that... We do in fact have Lael cranking away on a helmet for us as well! Of course, it's still a VERY early alpha build... but since you mentioned it, we may as well go ahead and wet some appetites...

View attachment 469867


@laellee uses Blender for most of his modeling, IIRC.

I can't wait to get my hands on any versions of the helmet floating around right now. It's such an exciting time!!!!

 

[ArkRaider]

This is awesome! I'm pretty excited that you'll be making these hollow to allow for electronics! I'm in for one.

 

[Sith4Life]

who would be a good source to put in the guts?

 

[ArkRaider]

who would be a good source to put in the guts?

Look up Shameem Moshrefzadeh on Facebook.

 

[Flagwaver]

A good detail about the Clip (? buckle) :
http://upload.dinhosting.fr/h/j/T/small_dn_tails_sabrelaser_KyloRen_attache.png

And I think it's painted Brass.
we can see the copper golden color on top.

About that. I think the 501st found out what the saber clip is and the belt clip. It's a stanchion queue barrier clip.

It slides on the belt rather than attaching with a covertec.

 

[KaanE]

It looks similar but it's not a match.

 

[joshvanrad]

It's similar, but Kylo's saber looks like it actually clips in.

 

[JJ Griffin]

About that. I think the 501st found out what the saber clip is and the belt clip. It's a stanchion queue barrier clip.

http://ecx.images-amazon.com/images/I/41rZv6vR0kL._SX425_.jpg

It slides on the belt rather than attaching with a covertec.

Similar in look and design but not the same, Kylo's saber-side has a spring-steel style "Clip" that clicks into a side notch.

 

[levallois]

I have not read in previous posts, but I could miss,
Would you have the dimentions of the hilt ? Priority the height ?

 

[Amnesiac]

Amazing. Count with me, really like this lightsaber's design.

 

[JJ Griffin]

I have not read in previous posts, but I could miss,
Would you have the dimentions of the hilt ? Priority the height ?

I'm sorry, mate, I don't understand the question, as you asking the dimensions of the hilt? Most importantly the height?

 

[RexKramer]

I think so JJ.

 

[Voodoo13]

Morning JJ, how's progress on the saber? Hoping to have that guy in hand sooner than later so I can get some guts and blades into it!

 

[JJ Griffin]

Funny that you ask, I actually started printing the Master last night... Here is what I have so far. I may reprint the "handle" section as it seems a bit short ATM... thinking maybe 2cm longer, maybe, but I want to wait for the pommel to finish so I can hold the main part of the body in my hand before I make a decision.

 

[RexKramer]

Looks pretty bad ass to me, sir!

 

[levallois]

I'm sorry, mate, I don't understand the question, as you asking the dimensions of the hilt? Most importantly the height?

Oops, sorry about that.
I realy need to practice my English.

As you said, I would like to know the dimention of the hilt,
and most importantly the dimention of the height (of the hilt).

Hope you'll understand this time.

 

[JJ Griffin]

I'm honestly not 100% sure, I'd like to be able to ask someone who saw it up close, but right now we're estimating somewhere between 30 and 35 cm. Our "grip" is around 5cm in diameter, to accommodate an internal diameter of a little over 3cm (to allow for electronics).

Hope that helps.

 

[levallois]

thank you for that.
it will help me.

Good continuations.

 

[lmakeltraln]

i'd be interested pending cost accouncement

 

[JJ Griffin]

Almost finished printing. Next comes the hard part-- clean-up and detailing...