Jedifyfe's Wearable NIKE MAG Upgrade DISPLAY VIDEO

Hey all, I don't know If anyone has touched on this and If they have I apologise for repeating but I thought it'd be helpful to those who want to do conversions. I've seen a lot of converters, Jedi included, who use a knife to remove the waffle grip from the shoe. A much easier and way quicker way is to use a hot air gun (the same you use to remove wallpaper) as it melts the glue without damaging the shoe. You can see from the pic what I mean.
 
lammy said:
Hey all, I don't know If anyone has touched on this and If they have I apologise for repeating but I thought it'd be helpful to those who want to do conversions. I've seen a lot of converters, Jedi included, who use a knife to remove the waffle grip from the shoe. A much easier and way quicker way is to use a hot air gun (the same you use to remove wallpaper) as it melts the glue without damaging the shoe. You can see from the pic what I mean.
Click to expand...


That's awesome lammy. Do you just heat gently from the outside and when it peels off, does it come off clean like that, or do you still have to scrape the bits of rubber off the yellow sole rubber?

Wish us lot knew all these little tips when we first did our conversions. I was sat in a room for weeks trying to figure out how to do a lot of this stuff :lol
 
lukebrynycz said:
That's awesome lammy. Do you just heat gently from the outside and when it peels off, does it come off clean like that, or do you still have to scrape the bits of rubber off the yellow sole rubber?

Wish us lot knew all these little tips when we first did our conversions. I was sat in a room for weeks trying to figure out how to do a lot of this stuff :lol
Click to expand...

Yeah dude, just leave it on the first setting and run over the first flap going back and fourth for about 10-15 seconds. It'll get a bit warm obviously but all you have to do is gently peel and tug as the glue lifts right up. Just keep it to little bits at a time and it'll come off like butter, no need to cut anything at all. This way there's no damage to the shoe and it'll be the best way to remove if anyone decides to change the sole completely.

Well I had a look on here before I started my KMAG conversions and saw that people were cutting into it but I didn't think it was the best way to go about it so I juuts got the old heat gun on it :)

Only issues I've got at the minute are:
*What glue to use to glue the shoe back together as I'll need a strong yet flexible resin (may just go with araldite)
*How to set up the lighting system on my mark poon mags-On my KMAG's I've used electronics from elwirecraft just to avoid soldering but it leaves me with the problem of the chunky connections which is no good for wearing. I need and inverter that runs off of a 9v battery like this http://i1095.photobucket.com/albums/i475/st200rich/nike air mag/IMAG0665.jpg but the only one I can find is from elwirecraft which brings me back to the chunky connector problem. I'll basically be running el strips in the strap and sole, but I don't know wether to go with LED's for the heel cup or not seeing as I haven't done any circuit making since college.
 
lammy said:
A much easier and way quicker way is to use a hot air gun (the same you use to remove wallpaper) as it melts the glue without damaging the shoe. You can see from the pic what I mean.
Click to expand...

Awesome the way that came away. Did you remove the entire sole this way as well?
 
cavx said:
Awesome the way that came away. Did you remove the entire sole this way as well?
Click to expand...

Unfortunately you can't remove the foam sole away from the KMAG shoe using the gun as all it does is cause the foam to expand. I had to use a craft knife to remove it as it was glued down a lot more securely than the mark poon MAG.
 
cavx said:
Thanks for that. So confirming what TheNickFox says about these shoes.
Click to expand...

Yeah, the KMAG's are a bit of a pain. Not impossible though. If you take your time with the knife and cut close to the upper shoe as possible without going through it, you'll be fine. I've nearly finished the conversion on my KMAG's, I just need to get a different inverter and I may end up cutting off the connector plugs and soldering the wires if they hurt my feet. We shall see.
 
cavx said:
Do you have a thread running on this?
Click to expand...

No I don't dude, I'll do a progression thread once they're done. Only thing is I don't think I'm going to bother with the heel LED's with the KMAG's. I've got another connection spare just in case I change my mind though
 
lammy said:
No I don't dude, I'll do a progression thread once they're done. Only thing is I don't think I'm going to bother with the heel LED's with the KMAG's. I've got another connection spare just in case I change my mind though
Click to expand...

hi
do you have any pics of your conversion to the kmags?
if so, just put them up in the knockoff mags thread.

since there are a few trying to convert the knockoff mags, it would be really helpful to see as many pics as possible

thanks
 
also, a question for jedifyfe and anyone who's got the mark poon or the real official mags.



Does anyone have any really high quality close up pics of the top part of the official nike mag?

how is the grey outer fabric connected to the top upper leather piece on them?
is the grey outer fabric just glued on to the main puffy foam filled leather upper piece?

this is the bit im confused on. I assume the Mark Poon's are glued on as well?
 
airair said:
also, a question for jedifyfe and anyone who's got the mark poon or the real official mags.



Does anyone have any really high quality close up pics of the top part of the official nike mag?

how is the grey outer fabric connected to the top upper leather piece on them?
is the grey outer fabric just glued on to the main puffy foam filled leather upper piece?

this is the bit im confused on. I assume the Mark Poon's are glued on as well?
Click to expand...


The top white part on the mark poon mags is a cotton like material, not pleather like the KMAG's. It's stitched on but the stitch is hidden by the fold. I'll try and post some pics up in a bit of my progression. Made a few mistakes mind you and I'm only using them as a trial and error pair. My mark poon ones are the ones I'm taking more time with. I'll probably make another pair of KMAG's in the future but i'm busy enough at the minute with these two conversions.
 
airair said:
also, a question for jedifyfe and anyone who's got the mark poon or the real official mags.



Does anyone have any really high quality close up pics of the top part of the official nike mag?

how is the grey outer fabric connected to the top upper leather piece on them?
is the grey outer fabric just glued on to the main puffy foam filled leather upper piece?

this is the bit im confused on. I assume the Mark Poon's are glued on as well?
Click to expand...

I have some offical mags and sent this pic to TheNickFox, I hope this is what you were looking for

2e2fkoh.jpg
 
Glad you found this thread! I was about to email you to ask if it was okay to post that very image here!

Thanks for helping out those of us who can't spring for the real deal!

-Nick
 
TheNickFox said:
Glad you found this thread! I was about to email you to ask if it was okay to post that very image here!

Thanks for helping out those of us who can't spring for the real deal!

-Nick
Click to expand...

Of course, its because of all you guys I even got in to all this as much as I did. This place became an obsession for me for a while after I did the hovering hoverboard project. But now I got my perfect outfit for comicon in a couple weeks. :)
IMAG0614.jpg
 
Last edited:
WOW that is one impressive outfit Dondula7.

Is it possible to post an image with the strap pulled out (in big loop, don't go pulling it out of the buckle) so we can see the collar a bit better? From what I can tell, the white part has been stitched, the outer fabric pulled up and glued in place, then the white part glued to that. I am guessing there is no stitch seam under the strap or is there?
 
cavx said:
WOW that is one impressive outfit Dondula7.

Is it possible to post an image with the strap pulled out (in big loop, don't go pulling it out of the buckle) so we can see the collar a bit better? From what I can tell, the white part has been stitched, the outer fabric pulled up and glued in place, then the white part glued to that. I am guessing there is no stitch seam under the strap or is there?
Click to expand...

I just took this with my phone, so I hope the quality is good enough, my DSLR battery is dead. Is this the area you're talking about. Jedi let us know if we are spamming your thread :cool

1492vtf.jpg
 
You must log in or register to reply here.

Similar threads

paulsboutique
F44AA Romulus Pulse rifle 3d design and build
2 3
Replies
52
Views
5,127
paulsboutique
paulsboutique
thatoneguy04
Pulse Rifle Ammo Counter Help
Replies
9
Views
669
laellee
laellee
PVmodels
List of tools and supplies to upgrade a Denix C96 for your DL-44
Replies
5
Views
740
PVmodels
PVmodels
A
First Handmade Samurai Armor | Ghost of Tsushima Inspired | Amateur Build
Replies
4
Views
799
joberg
joberg
S
Solo Conveyex 20-T Railcrawler Transport
Replies
1
Views
276
joberg
joberg
Back
Top