Han In Carbonite in Canada - Build thread

Nipple madness

Took me about !5 minutes to clean, wash and dry all 35!

image1.jpeg image2.jpeg image3.jpeg

Primered. Placed for color check only. And I think I'll leave them that way...

image4.jpeg image5.jpeg image7.jpeg image6.jpeg

It has a nice bluish look to it that is very screen used!!

IMG_2987.JPG IMG_2984.JPG IMG_2985.JPG IMG_2986.JPG

Screen prop (thanks to Loanstar for those amazing pics btw)

R2 hic-loanstar-5.jpg L3 Panel 8.jpg
 
Last edited:
I tested both hot glue and super glue and one hurts more than the other!! Super glue is the way to go though as hot glue can pop super easily!
 
Last edited:
Bigturc said:
Hopefully, last layer of bondo to correct the remaining small imperfections on the box.

Also planning the wall mount for this. I weighted the whole box without the volvo side panels at 78lbs. I'm planning to buy a TV rack like this:
http://www.monoprice.com/product?c_id=109&cp_id=10828&cs_id=1082822&p_id=4114&seq=1&format=2. This one is 32" large so would be hidden behind the box.

View attachment 593115

Anyone has objection or tried anything else?
Click to expand...

I used a similar model and it has been rock solid. Just make sure to anchor it into the studs and you'll be fine.
 
Small work on the Hero 2 panel.

I wanted to replicate the darker border edge within the Bronica frame as seen here...
R2 hic-loanstar-7.jpg

Figured out what surface the Bronica part was hiding and taped the edge...
IMG_3028.JPG

Then more paper to protect the panel.
IMG_3029.JPG

Remove tape and Bronica in place.
IMG_3030.JPG

Close enough! :thumbsup
IMG_3032.JPG
 
Good spot... I didn't even notice that when I built mine. I'll need to add it as a separate layer now. :thumbsup
 
What colours did you end up with for your panels and greeblies? I've seen a lot of people just using the grey primer.
 
Between two errands, I had time this week end to go buy some racks! Found a fixed rack, good up to 165 lbs. I just needed about 80 but better safe than sorry. This cost me about 30$ usd. Really cheap but terribly solid.

IMG_3047.JPG

Installed on wall, I decided to install it closer to the center of the box instead of too high to preven being able to pull on it (kids) from the bottom and risking damaging anything. Here's an approx look of how the brackets get mounted on the box. Plywood installed on the side 2x3. I just need to figure out how much space I want between the box and the walls. I have no idea yet.

IMG_3041.JPG IMG_3043.JPG

To do all this, I had to flip my box, and sit it on each side. Don't forget to give Han some breathing room in there!

IMG_3044.JPG
 
It is so satisfying to finally hang it up. You'll find yourself standing there staring at it for no reason other than it makes you happy.
 
QCWolf said:
It is so satisfying to finally hang it up. You'll find yourself standing there staring at it for no reason other than it makes you happy.
Click to expand...

Hahaha .. that made me laugh .. that's exactly what I plan to do .. figure out proper lighting too! Luckily, I have a light right over it too!
You are so right Wolf!!! I want to hang it now, and it's not even painted! :) It would finally clear the garage for our next project though! :) Soon .. soon!
 
What I wanted to do is fix a 2x4 to the middle and top lateral 2x3s .. but I can't do it since I still haven't received my MC plugs that I ordered back in october. Until I have them, I don't want to place anything close to that area for I'm affraid to have the support in the way of whatever I'm gonna have to do in that area. Also, I'm not even sure how the fitting is of the MC plugs in the Zenix box. I'm not too affraid of the work if it doesn't fit, but I'd still love to know ..

IMG_3043.JPG

Another note about those plugs .. when ordered, it was an 8 to 12 months delivery delay. I'm now at my 19th months and no news from Jeff. I tried sending them an email asking for a true realistic ETA on when those will be ready or at least, where I am on the payment list. No reply either. I don't mind about delays - anyway I'm not ready yet to paint it - but there's nothing I hate more than radio silence on a seller's part. They were quick enough when it was time to send payment though ...

Let's hope that it's just a temporary thing and that I'll get those plugs soon! If you planned on having those in your box, order them now, it's about 100$ + 60$ shipped in Canada.
 
Just spend 2 hours on this. Wall mount is now done!!

2 vertical side mount added between middle and top ones. Then a cross bar between those and the middle ones. The plywood you see in the third picture was dropped onto the horizontal bars. All pieces were glued in place .. hopefully, it's solid enough .. it's only 80 lbs after all!

Forgot to take pictures of the mounted brackets! :wacko but you get the picture!!

image1.jpeg image2.jpeg image3.jpeg

Then flipped again and new holes were puttied. I need one last coat of primer and if everything goes well, paint should go in next!!!

image4.jpeg image5.jpeg
 
Had some help this morning to get this on the wall. I wanted to make sure that everything was fine before finalizing the paint work on this.
Happy to report that this is a total success! It's leveled, and first perfectly on the rack!

Excuse the ugly iphone pics .. there's gonna be much more soon! :)

IMG_3055.JPG IMG_3056.JPG IMG_3057.JPG
 
You must log in or register to reply here.

Similar threads

jcoffman99
Han in Carbonite ?
Replies
3
Views
365
laellee
laellee
zenix
Unlimited Run Han in Carbonite Panel 2 Greeblie upgrade kit
Replies
12
Views
1,192
zenix
zenix
Redman2187
Han in Carbonite H.I.C. Resto-build
Replies
16
Views
3,862
Hanamaid
Hanamaid
Austin Mac
ESB BOBA FETT EE3 Resin/FDM Printed Build First Thread
Replies
6
Views
388
BudaFett
BudaFett
Ryan Clinton
Interest Boushh helmet full greeblie screen accurate kit
Replies
2
Views
537
HighlanderFX
HighlanderFX
Back
Top